First, make sure the ABS module is to blame
The ABS warning light is most often triggered by a wheel speed sensor, its wiring or the reluctor ring by the wheel bearing, rather than by the module itself. Before you pay for a repair, read the fault codes with a diagnostic tool that can talk to the ABS module, and check the fuses, the power supply, the earth and the connector. Signs that point to the module are internal module faults, faults with the pump motor or the valves, faults on several sensors at once, or no communication with the module despite a good power supply. We describe the whole procedure in our guide on how to test an ABS module - failure symptoms and checks.
What does ABS module repair and reconditioning involve?
An ABS unit consists of a metal hydraulic block with the valves and the pump motor, and the control module (the ABS pump controller), i.e. the electronics in a plastic housing bolted to the block. It is the electronics that fail more often, and on many units (e.g. Bosch, ATE) the control module can be unbolted and repaired on its own, without opening the hydraulic brake system.

A Bosch ABS pump from an Audi. The black housing on top is the control module, with the metal hydraulic block and the pump motor below it.
An automotive electronics specialist tests the module, opens the housing and looks for the damaged component. The parts most often repaired or replaced are:
- cracked solder joints, caused by vibration and changes in temperature, which make the fault come and go;
- the transistors and the relay that drive the pump motor and the valves, which usually burn out after a short circuit or an overload;
- the valve coil connections: the coils sit in the module housing and slide over the valves in the block;
- corroded connector pins, as long as the water has not yet reached the circuit board.
After the repair, the module should pass a test, and once it is back in the car, the fault codes need to be cleared, the ABS checked with a diagnostic tool and the car taken for a test drive.
Which ABS faults can be repaired and which cannot
A repair has the best chance of success when a single, known component is damaged and the circuit board and processor are intact. The chances are slim after water damage or a burnout, because corrosion carries on spreading even after drying and a short circuit destroys the tracks inside the circuit board (find out more in our guide to a water-damaged or burnt-out ABS pump control module). Repairing the electronics will not help much either if the valves or the pump motor in the block are damaged - in that case the whole ABS pump is usually replaced. Be careful, too, if the same fault comes back after an earlier repair or the housing has already been opened and no longer seals properly.
How much does ABS module repair or ABS pump replacement cost?
Whether you are getting quotes in the UK or in Ireland, there is no single figure for the ABS pump repair cost or replacement cost, because it all depends on the type of module, the kind of fault and the car model. When you compare quotes, add up the total:
| Control module repair | Used control module or pump | New module from a main dealer |
| What you pay for | diagnosis, the repair, removal and refitting, sending it to the specialist | a part with the same numbers, fitting, coding and calibration, plus bleeding for a complete pump | the same as for a used part; usually the most expensive option |
| Coding | usually not needed - the same module goes back in | on many cars it has to be coded with a diagnostic tool | on many cars it has to be coded with a diagnostic tool |
| Time | sending it off and the repair itself, with the car off the road | dispatched from stock | sometimes unavailable for older cars |
| When to choose it | a minor, known electronic fault; a part that is hard to find | after water damage or a burnout, a hydraulic fault, a fault that keeps coming back, or when you need the car back quickly | when no used part with those numbers is available |
After a repair, you cannot always be sure that other components on the circuit board have not been weakened, whereas we check every used part on a test bench before dispatch. You will find current prices in our Complete ABS Pump and ABS & ESP Control Modules categories.
How to choose a used ABS module or pump
A part is matched by its numbers, not by the car model, because even within the same model ABS modules differ in version and software, e.g. depending on whether the car has ESP. Write down the numbers on the control module label: the module manufacturer's part number (on Bosch units it starts with 0 265) and the car manufacturer's part number (on a Volkswagen, the control module number is in the format 1K0 907 379 and the complete pump number 1K0 614 517). Add the hardware and software versions (HW, SW) if they are on the label and, if you are buying a complete pump, the numbers on the hydraulic block as well.

The label on a Bosch control module: the Bosch number 0 265 109 026 and the Audi number 4D0 907 379 F. Both must match when you buy a replacement.
If you are not sure, send us a photo of the label and we will check which module fits.
ABS module or ABS pump replacement step by step
- Make sure the ABS module is to blame: check the wheel speed sensors, the fuses, the power supply, the earth and the connector.
- Write down the numbers from the old module and the block, then choose a part with the same numbers.
- If the hydraulics are working, replace just the control module: it unbolts from the block without undoing the brake pipes.
- If you are replacing the complete pump, fit it and bleed the brake system; on many cars this is done with a diagnostic tool.
- Code the module to the car's equipment and calibrate the sensors if the car requires it, e.g. the steering angle sensor on cars with ESP.
- Clear the fault codes, check that the ABS and ESP lights go out and take the car for a test drive.
ABS pumps and ABS modules at Auto24Parts
We mainly sell used, original ABS pumps and ABS modules, and some models have been reconditioned. Before dispatch, every part is checked on a test bench: electrically, electronically, visually and mechanically. Used parts come with a 6-month warranty, and you can return a part within 14 days of receiving the parcel (warranty and returns policy).
Not sure which module fits? Email a photo of the control module label and the numbers from the hydraulic block to contact@auto24parts.com and we will check compatibility before you buy. We ship by DHL Express or FedEx Express, and delivery within Europe, including the UK and Ireland, usually takes around 1-2 working days from dispatch. You will see the exact shipping cost at checkout once you enter your address. The UK is outside the EU, so customs duties and import charges may be payable by the recipient (shipping and delivery).
Frequently asked questions
Can you drive with faulty ABS?
The car will still brake, but without ABS, and usually without ESP too, the wheels can lock under hard braking on a wet or slippery road. In the UK, an ABS warning light showing a system malfunction is a major defect under section 1.6 of the MOT inspection manual, so the car will fail its MOT until the fault is fixed. In Ireland, the same fault is a major deficiency under the EU rules followed by the NCT.
Does an ABS module need coding after a repair?
Usually not, because you get back the same module with your car's data. After fitting, clear the fault codes and check the ABS with a diagnostic tool.
Can a water-damaged ABS module be repaired?
Rarely with any lasting success. Water causes corrosion that keeps spreading even after drying, and once the housing has been opened it no longer seals properly. That is why, after water damage, the usual choice is a replacement part with the same numbers.
Legal position as of 6 November 2026: Directive 2014/45/EU on periodic roadworthiness tests for motor vehicles and their trailers, Annex I, point 1.6, and Article 9; in the UK, the MOT inspection manual for private passenger and light commercial vehicles, section 1.6. AI tools were used in preparing this text.