A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump BMW E60 Bosch 0265236006 6768550 0265950409
Vendors's code: 0265950409
Product code: 0265236006
Barcode:
Code 39:
ISBN:
325,20 zł
Price
325,20 zł
400,00 zł
Price
400,00 zł
Ask about the product
ABS pump BMW E60 Bosch 0265236006 6768550 0265950409
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Does ABS pump 0265236006 come complete with the control unit?
Used ABS pump with control unit, number 0265236006, inspected before sale. Matched by the numbers on the block and sticker.
Used BMW E60 ABS pump with number 0265236006
ABS pump 0265236006 for BMW E60 is a used original module that regulates brake pressure when a wheel starts to lock up. It is matched by the numbers on its labels, not by the car model alone. According to the listing, the pump comes from the BMW E60 model.
Where to find the numbers on an ABS pump
You will find the numbers on the labels, while catalogues list them as a single string:
- 6768550, BMW number in short form, without the group prefix,
- 0 265 236 006 (catalogue format: 0265236006), hydraulic block manufacturer's number,
- 0 265 950 409 (catalogue format: 0265950409), control unit number.
The full numbers matter, including their endings. If in doubt, send us a photo of your pump.
What can point to an ABS pump failure
- valve or pump motor faults are stored in the control unit memory,
- the pump motor switches on at unusual moments or runs louder than usual,
- brake fluid leaks from the hydraulic block, which requires immediate action,
- on a slippery surface the wheels lock up noticeably sooner than they used to.
Before buying a module, read the fault codes with a diagnostic tester. A faulty wheel speed sensor or its wiring can cause the same symptoms, and in that case replacing the pump will not help. After replacement the fault codes usually need to be cleared, and if the brake lines have been disconnected, the system must be bled.
Questions and answers
| Are the pump and the control unit sold separately? |
|---|
| In this listing they are a single module: a hydraulic block with the pump and valves, with the control unit attached to it. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| Who makes this module? |
| The module is made by Bosch. The manufacturer's name does not change the numbers you should use to match the part. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Want to check before you buy? Send a photo of the block and sticker on your ABS pump and we will check that the numbers match.
