A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump Smart Bosch 0265230390 0265951118
Vendors's code: 0265230390
Product code: 0265951118
Barcode:
Code 39:
ISBN:
£123.33
Price
£123.33
£151.70
Price
£151.70
In stock
Ask about the product
ABS pump Smart Bosch 0265230390 0265951118
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£22.75
-
shipping
(Poland)
from
£22.75
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
When is ABS pump 0265230390 the right choice for your Smart?
Used ABS pump with control unit, number 0265230390, inspected before sale. Matched by the numbers on the block and sticker.
Used Smart ABS pump with number 0265230390
The hydraulic block and control unit of this ABS pump form a single module that works with the wheel speed sensors in Smart cars. You will find number 0265230390 on the label, and the full set of numbers is given in the description below. The listing does not state the car model or year, so we do not give them here and match the part by its numbers.
Part number 0265230390 and related numbers
The numbers as written on the labels and as a single string, the way catalogues list them:
- 0 265 230 390 (catalogue format: 0265230390), hydraulic block manufacturer's number,
- 0 265 951 118 (catalogue format: 0265951118), control unit number.
Matching by number is more reliable than matching by car model. Compare all the numbers and ask us if any of them does not match.
What can point to an ABS pump failure
- valve or pump motor faults are stored in the control unit memory,
- the pump motor switches on at unusual moments or runs louder than usual,
- the ABS warning light comes on together with the stability control warning light,
- the ABS switches itself off shortly after the engine is started.
ABS faults should not be ignored, because without anti-lock protection the car brakes less well on wet or slippery roads. Diagnosis and fitting are best left to a garage with a suitable scanner.
Questions and answers
| Which car model does this pump fit? |
|---|
| The listing does not state a model or year, so confirm compatibility with the number from the original pump in your car, or send us a photo of it. |
| Does a lit ABS warning light always mean a faulty pump? |
| No. Read the fault codes first, because the cause may be a wheel sensor, its wiring or too low a supply voltage. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Not sure about the match? Send us a photo of the numbers on your ABS pump and we will check whether this module will fit.
