A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine control unit Ford Transit 2.5 Diesel 98VB9J464ZD
Vendors's code: 98VB9J464ZD
Product code: 98VB-9J464-ZD
Barcode:
Code 39:
ISBN:
1 138,21 zł
Price
1 138,21 zł
1 400,00 zł
Price
1 400,00 zł
Ask about the product
Engine control unit Ford Transit 2.5 Diesel 98VB9J464ZD
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Is engine control unit 98VB9J464ZD a used original part?
Used Ford engine control unit with number 98VB9J464ZD. Send us the numbers from the label on your control unit.
Used engine control unit for Ford Transit with number 98VB9J464ZD
According to the listing, this is a control unit for Ford Transit with a 2.5 Diesel engine. Control unit 98VB9J464ZD is a used original module, and its numbers help tell it apart from similar versions. The listing states that this control unit is for: Ford Transit. Engine given in the listing: 2.5 Diesel.
Control unit numbers and markings
You will find the numbers on the label of the control unit, while catalogues list them as a single string:
- 98VB-9J464-ZD (catalogue format: 98VB9J464ZD), car manufacturer's original number.
Check the numbers on your control unit and compare them with those above. If any of them differs, contact us before ordering.
What engine starting problems can indicate
- the diagnostic tester cannot connect to the control unit,
- the car loses power or goes into limp mode,
- starting is blocked by the immobiliser after the electronics have been replaced or repaired,
- the housing or connector of the control unit shows signs of water ingress or corrosion.
Before buying a control unit, read the fault codes with a diagnostic tester and check the power supply, the earth connections and the connector. Damaged sensors, wiring or fuses can cause similar symptoms, and in that case replacing the control unit will not help.
Questions and answers
| Where do I find number 98VB9J464ZD on my control unit? |
|---|
| The numbers are on a sticker or printed on the housing of the control unit. Take a close-up photo of the label in good light so that all the characters can be read. |
| Does a lit engine warning light always mean a faulty control unit? |
| No. Read the fault codes first, because the cause may be a sensor, the wiring or the power supply. |
| Does this control unit fit the 2.5 Diesel engine? |
| According to the listing it does, but confirm this with the numbers from the original control unit, because a single model comes with different versions. |
| What is the condition of this control unit? |
| It is an original recycled part in good condition, checked by us. Warranty details are in the product features table. |
Not sure about the match? Send us a photo of the label on your control unit and we will check whether this part will fit.
Customers Also Viewed
-
Price 700,00 złPrice 569,11 zł
-
Price 800,00 złPrice 650,41 zł
