A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen Bosch 070906016D 0281010736
Vendors's code: 0281010736
Product code: 0281010736
Barcode:
Code 39:
ISBN:
$207.95
Price
$207.95
$255.77
Price
$255.77
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine Control Unit Volkswagen Bosch 070906016D 0281010736
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
$30.69
-
shipping
(Poland)
from
$30.69
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Does the 070906016D ECU fit your Volkswagen?
Check the label on your module: if it shows VW number 070906016D and Bosch number 0 281 010 736, it is the same version. Compatibility is decided by the numbers, not the model alone.
Engine Control Unit Volkswagen Bosch 070906016D 0281010736
The module with VW number 070906016D is a Bosch engine control unit, recognisable by its manufacturer's number from the 0 281 group, which is intended for diesel engines. In a Volkswagen it manages fuel injection and starting, and logs fault codes when problems occur. We sell it used, working and in good condition.
How to identify this module
- 070906016D – VW part number, with a single letter D
- 0281010736 – Bosch number, as on the label: 0 281 010 736
The single letter D indicates the software or hardware version. If your ECU has a different letter, or two letters, after 070906016, it is a different version – ask us before buying.
Symptoms of a faulty ECU
- no start despite a working starter motor,
- the engine cutting out unexpectedly,
- no communication with the diagnostic tool,
- running in limp mode and poor acceleration.
First check the power supply and earths, and inspect the connector pins – these are the most common sources of problems unrelated to the module itself. It is also worth reading the fault memory before removal.
Choose your ECU version
We sell the ECU in two versions. The locked version contains the data and immobiliser of the Volkswagen it was removed from – it is bought by workshops that unlock, program and adapt ECUs themselves. The unlocked version is prepared before dispatch, usually within 1–2 working days.
The method used (PIN / CAR PASS, Virgin, IMMO OFF, auto programming, clone) depends on the number, software and immobiliser, so not every one is an option. Before buying, ask what is possible. Full description: ECU preparation options.
Questions and answers
| My number is 070906016 with two letters. Will this one fit? |
|---|
| That is a different version. Send a photo of the label and we will check whether 070906016D can be used. |
| Is the Bosch number needed? |
| Yes, it helps confirm that it is the same hardware. |
| When will you dispatch the unlocked version? |
| After preparation, which usually takes 1–2 working days. |
| Condition and warranty? |
| Used, working, in good condition. You will find the warranty period in the product features table. |
Any questions? Email us at contact@auto24parts.com.
