A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen Lupo Bosch 045906019AE 0281010628
Vendors's code: 0281010628
Product code: 0281010628
Barcode:
Code 39:
ISBN:
227,64 zł
Price
227,64 zł
280,00 zł
Price
280,00 zł
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine Control Unit Volkswagen Lupo Bosch 045906019AE 0281010628
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Where can I find the number 045906019AE on a Volkswagen Lupo ECU?
Look for it on the label on the module casing, next to Bosch number 0281010628 (written as 0 281 010 628). This diesel engine ECU is used and fully working.
Engine Control Unit Volkswagen Lupo Bosch 045906019AE 0281010628
The small diesel Lupo needs an ECU with exactly the same number as the original – in this case 045906019AE. The module was made by Bosch and marked with number 0281010628. The ECU is responsible for fuel injection and the engine ancillaries, and when it fails the result is most often a no-start.
Numbers to check
- 045906019AE – Volkswagen part number – the basis for matching
- 0281010628 – Bosch number, shown on the label as 0 281 010 628; the 0 281 prefix denotes a diesel ECU
The letters AE at the end of the VW number describe the software or hardware version. 045906019 numbers come with various suffixes, so it matters that the whole number matches.
Fault symptoms
- no start although the starter motor works,
- engine warning light and loss of power with no faulty sensor,
- communication with the module dropping out during diagnostics,
- problems after a battery change or a short circuit in the wiring.
Before ordering an ECU, check the fuses and earths – they are cheaper causes of the same symptoms.
Locked, unlocked and preparation methods
In the locked version the ECU stores the data and immobiliser of the Lupo it came from – we offer it to workshops that will unlock, program and adapt it themselves. In the unlocked version we prepare it before the parcel is sent, usually within 1–2 working days.
Whether PIN / CAR PASS, Virgin, IMMO OFF, auto programming or clone can be used is decided by the part number, software and immobiliser. Please ask us before you buy. Full description: engine control unit options.
Questions and answers
| Will the 045906019AE module start the Lupo without programming? |
|---|
| The locked version – no. The unlocked version depends on the chosen method, which we agree before purchase. |
| My number is 045906019 with a different suffix – will it fit? |
| Not necessarily. Send a photo of the label and we will compare the versions. |
| What condition is this ECU in? |
| It is a used, fully working part in good condition. You will find the warranty period in the product features table. |
Send any queries about the numbers to contact@auto24parts.com – we will reply before you buy.
