A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Refurbished ABS pump Volkswagen Seat Skoda ATE 1K0907379AD 1K0614517BD
Vendors's code: 1K0907379AD
Product code: 1K0614517BD
Barcode:
Code 39:
ISBN:
$499.07
Price
$499.07
$613.86
Price
$613.86
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Refurbished ABS pump Volkswagen Seat Skoda ATE 1K0907379AD 1K0614517BD
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
$30.69
-
shipping
(Poland)
from
$30.69
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
What does number 1K0907379AD on an ABS pump mean?
Refurbished ABS pump with control unit, number 1K0907379AD, inspected before sale. Compare the numbers with the original in your car.
How to identify ABS pump 1K0907379AD for your Volkswagen Seat Skoda
This is a refurbished ABS pump with a control unit for Volkswagen Seat Skoda cars: an aluminium hydraulic block with valves and a pump motor, with the electronics bolted to it. The main number is 1K0907379AD, and the other numbers from the listing are given below. According to the listing, the module was inspected before sale. According to the listing, the pump comes from the Volkswagen Seat Skoda model.
Numbers to compare
You will find the numbers on the labels, while catalogues list them as a single string:
- 1K0614517BD, original Volkswagen number,
- 1K0907379AD, Volkswagen control unit number.
Matching by number is more reliable than matching by car model. Compare all the numbers and ask us if any of them does not match.
What can point to an ABS pump failure
- the ABS warning light comes on after the engine is started and stays on,
- valve or pump motor faults are stored in the control unit memory,
- the ABS activates for no reason during normal braking,
- the ABS switches itself off shortly after the engine is started.
First check the wheel sensors, their wiring and the supply voltage. Only a fault code pointing to the module justifies replacing the pump. After fitting, clear the fault codes and, if necessary, bleed the brake system.
Questions and answers
| What is the difference between numbers 1K0907379AD and 1K0614517BD? |
|---|
| The module carries several numbers, because it is identified both by the car brand and by the manufacturer of the block and control unit. When matching the part, compare all the numbers. |
| Are the pump and the control unit sold separately? |
| In this listing they are a single module: a hydraulic block with the pump and valves, with the control unit attached to it. |
| Who makes this module? |
| The module is made by ATE. The manufacturer's name does not change the numbers you should use to match the part. |
| What condition is this pump in? |
| It is a refurbished module, not a new part. According to the listing, it was inspected before sale. You will find the warranty period in the product features table. |
Want to be certain? Send us the numbers from the block and sticker on your ABS pump, and together we will check whether this part will fit.
