A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Suspension control module BMW E60, E61 Bosch 0277022048 1279H04864
Vendors's code: 0277022048
Product code: B413-544EB
Barcode:
Code 39:
ISBN:
£276.80
Price
£276.80
£340.46
Price
£340.46
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Suspension control module BMW E60, E61 Bosch 0277022048 1279H04864
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£22.70
-
shipping
(Poland)
from
£22.70
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Looking for a suspension control module for the BMW E60, E61?
This is a used, working suspension control module for the BMW E60, E61 - numbers 0277022048 / 0 277 022 048 / 1279H04864. Before buying, compare the numbers with the label on the control module in your car.
Suspension control module BMW E60, E61
This listing is for a used, working suspension control module for the BMW E60, E61. The part is in good condition.
Numbers to compare
- 0277022048 / 0 277 022 048 - Bosch number
- 1279H04864 - additional Bosch number
Fitment
Compare number 0277022048 in full with the number on your control module. Different versions of suspension control modules were fitted to the same models, so the number decides the fit, not the model alone.
Symptoms of a faulty suspension control module
- a suspension message appears right after the engine is started,
- the suspension height or stiffness cannot be changed,
- the car does not sit level on all four wheels,
- the control module does not respond to tester commands.
Before you buy a control module, check the fuses, power supply, earths and connectors - a faulty height sensor or compressor causes similar symptoms.
Questions and answers
| Is the control module new? |
|---|
| The control module is used, but in working order. The warranty is given in the product features. |
| Why is the number written in several ways? |
| The same number on the housing may be written with spaces or as one string. We give both forms to make it easier to find. |
| Where do I find the number on the control module? |
| The number is on the label or housing of the control module removed from the car. If you cannot read it, send us a photo. |
Send fitment questions to contact@auto24parts.com - give the model, year and the number from the control module.
