A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump and control module Suzuki SX4 Bosch 5611080JC0 0265235159 0265950590
Vendors's code: 0265235159
Product code: 0265950590
Barcode:
Code 39:
ISBN:
€487.80
Price
€487.80
€600.00
Price
€600.00
Ask about the product
ABS pump and control module Suzuki SX4 Bosch 5611080JC0 0265235159 0265950590
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
When is ABS pump 5611080JC0 the right choice for your Suzuki?
Used ABS pump with control unit, number 5611080JC0, inspected before sale. Matched by the numbers on the block and sticker.
Used Suzuki ABS pump with number 5611080JC0
ABS pump 5611080JC0 for Suzuki is a used original module that regulates brake pressure when a wheel starts to lock up. It is matched by the numbers on its labels, not by the car model alone. The labels show no model or year, so we do not state them here and match the part by its numbers.
Where to find the numbers on an ABS pump
Below are the numbers as they appear on the labels, together with the single-string form used in catalogues:
- 56110-80JC0 (catalogue format: 5611080JC0), Suzuki number stamped on the hydraulic block,
- 0 265 235 159 (catalogue format: 0265235159), hydraulic block manufacturer's number,
- 0265950590, control unit number.
The full numbers matter, including their endings. If in doubt, send us a photo of your pump.
What ABS problems can point to
- the ABS activates for no reason during normal braking,
- brake fluid leaks from the hydraulic block, which requires immediate action,
- the ABS warning light comes on together with the stability control warning light,
- on a slippery surface the wheels lock up noticeably sooner than they used to.
ABS faults should not be ignored, because without anti-lock protection the car brakes less well on wet or slippery roads. Diagnosis and fitting are best left to a garage with a suitable scanner.
Questions and answers
| Where do I find number 5611080JC0 on my pump? |
|---|
| The numbers are stamped or printed on the aluminium hydraulic block, and the control unit has a separate sticker. Take a close-up photo of both places in good light. |
| Are the pump and the control unit sold separately? |
| In this listing they are a single module: a hydraulic block with the pump and valves, with the control unit attached to it. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| What condition is this ABS module in? |
| It is an original recycled part in good condition, checked by us. Warranty details are in the product features table. |
Want to check before you buy? Send a photo of the block and sticker on your ABS pump and we will check that the numbers match.
