Skip to main content
English €
English €
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English €
English €
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Why a used engine control unit has to be prepared

The engine control unit (ECU) works together with the immobiliser, the car's anti-theft system. The key, the immobiliser module or body control module (e.g. BSI, BCM) and the ECU 'know' each other, and the ECU's memory holds data from the car it came from: the immobiliser data, often the VIN and the equipment coding. Fit that ECU to another car and the immobiliser will not let the engine start, even if the ECU has exactly the same part number and comes from the same model.

That is why a used ECU has to be matched to your car: programmed by a garage, cloned from your old ECU or bought together with the immobiliser components. Our guide to ECU refurbishment or replacement explains the whole replacement process and what affects its cost.

ECU programming, coding and cloning - what they mean

These terms come up in every conversation about a used ECU, and they are easy to mix up:

TermWhat it involvesWhen it is needed
Programminga garage pairs the ECU with the immobiliser and key using a diagnostic tool, sometimes with a PIN code or CAR PASSwith a Virgin ECU or an ECU whose code has been read out
Codingsetting the ECU up for the car's version and equipmenton many cars, after programming
Cloningtransferring the data from your old ECU to a working ECU with the same numberswhen the old ECU can still be read
Virgin ECUan ECU wiped of the previous car's data, ready to be programmedwhen the garage has programming equipment

Programming and cloning do not change the engine's performance. They are only about making the ECU recognise your car and your key, so they have nothing to do with remapping or chip tuning.

How our ECU cloning service works

With cloning, you send us your old ECU, and we supply a working replacement with matching numbers. We then transfer the immobiliser data, the car's configuration, the coding, the VIN and the other information the engine needs to start from your old unit to the replacement. If the cloning is successful, the replacement ECU is ready to fit with no further programming in the car, so you do not need a garage with an ECU programmer.

There is one condition: the memory and processor of your old ECU must be readable. Preparation adds around 1-2 working days to your order, plus the time it takes to send us your old ECU. Cloning is possible for many ECUs, including those from Mercedes-Benz, BMW, Ford, Kia, Toyota and Jeep.

Bosch engine control unit from a Peugeot, part number 0 281 037 198
A Bosch engine control unit from a Peugeot (0 281 037 198). For ECUs like this, cloning is sometimes the only preparation option, so we always check by part number which variants are available.

Which ECU variant should you choose?

We sell used ECUs in three forms: Locked, Unlocked (in one of the variants 2a to 2e) or as a Full Set. This table will help you choose:

VariantWhat you do after fittingWhen it is a good choice
1. Locked ECUa garage reads the data, unlocks the immobiliser, then programs and codes the ECUyou have access to a garage with programming equipment
2a) ECU with PIN Code / CAR PASSa garage enters the code and pairs the ECU using a diagnostic toolthe car needs a security code, e.g. some Vauxhall and Opel models
2b) Virgin ECUa garage programs, codes or adapts the ECUe.g. some Renault, Peugeot, Fiat, Citroën and Alfa Romeo ECUs
2c) Plug & Play - IMMO OFFyou fit it; the immobiliser function in the ECU is disabled or modifiedselected ECUs only, e.g. from VW, Audi, Škoda and Fiat
2d) Plug & Play - Auto Programmingyou fit it; the ECU takes the data it needs from the other modules by itself, as long as it can communicate with the BSI or BCM, the immobiliser and the keye.g. some Peugeot, Citroën, Fiat and Alfa Romeo models
2e) Plug & Play - Cloneyou fit it; the data has been transferred from your old ECUyour old ECU can still be read
3. Full Set (Plug & Play)you fit every part of the set: the ECU and the immobiliser components, e.g. the immobiliser module, ignition switch and keycloning is not possible, or you need a complete matched set

Not every variant is possible for every ECU. It depends on the full part number, the ECU manufacturer, the car model, the software version and the type of immobiliser. The details of each variant are on our ECU preparation options page.

IMMO OFF is not the same as Virgin. In this variant, the immobiliser function in the ECU is disabled or modified, so if you want to keep your car's anti-theft protection, choose cloning or programming.

If the ECU cannot be cloned

Cloning needs the old ECU's memory and processor to be working. If the ECU has been flooded or burnt out, they are sometimes damaged and the data cannot be read. You are then left with a Virgin ECU or an ECU with a PIN code, programmed by a garage, or a Plug & Play Full Set. A Full Set only works if you fit every part supplied, because leaving out a single module can stop the car from starting. What to do with a damaged ECU is covered in our guides on flooded and burned engine control units.

How to match the ECU and the variant by part number

The variant is chosen by part number, not by the car model. Write down or photograph all the numbers on the label: the car manufacturer's part number and the ECU manufacturer's part number (e.g. Bosch, Siemens, Continental, Delphi, Magneti Marelli, Denso). The make, model, year, engine size and gearbox type also help.

Label of a Bosch 0 281 014 209 engine control unit with the Fiat number 51799349
A Bosch engine control unit from a Fiat Ducato 2.3 JTD. The label shows the Bosch number 0 281 014 209 and the Fiat number 51799349 - both must match when you buy a replacement.

Send us these numbers or a photo of the label before you place your order. We will check whether a Locked ECU, one of the Unlocked variants or a Full Set is right for your car.

Engine control units at Auto24Parts

We mainly sell used original engine control units, and some models have been refurbished. Before dispatch, we check every ECU on a test bench: electrically, electronically, visually and mechanically. Used parts come with a 6-month warranty, and you can return a part within 14 days (see our warranty and returns policy). ECU preparation services (e.g. Virgin, IMMO OFF, Clone, coding) are non-refundable.

Email us at contact@auto24parts.com. We ship by DHL Express or FedEx Express. Delivery within Europe, including the UK and Ireland, usually takes around 1-2 working days from dispatch. You will see the exact shipping cost at checkout once you have entered your address. As the UK is outside the EU, the recipient may have to pay customs duties and import charges (shipping and delivery).

Frequently asked questions

Will an ECU from the same car model work without programming?

Usually not. It still holds the immobiliser data and other details of the previous car, so without cloning, programming or a Full Set the engine will not start, even if the ECU number is identical.

Does the car need any programming after ECU cloning?

No. After successful cloning, you fit the ECU with no further programming. Before fitting it, though, fix whatever caused the old ECU to fail, e.g. a short circuit in the wiring loom or moisture, otherwise the replacement may be damaged in the same way.

How long does ECU preparation take?

Preparing an Unlocked ECU adds around 1-2 working days to your order. For cloning, you also need to allow time to send us your old ECU.