The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine Controller SKODA FABIA 1.2 TDI DELPHI 28281647 03P906021K DCM3.7
Vendors's code: 03P906021K
Product code: 28281647
Barcode:
Code 39:
ISBN:
1 138,21 zł
Price
1 138,21 zł
1 400,00 zł
Price
1 400,00 zł
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller SKODA FABIA 1.2 TDI DELPHI 28281647 03P906021K DCM3.7
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU ENGINE CONTROLLER SKODA FABIA 1.2 TDI DELPHI 28281647 03P906021K DCM3.7
Tested ECU engine controller by Delphi for Skoda Fabia 1.2 TDI with part numbers 28281647 and 03P906021K, comes with warranty and fast shipping.
ECU Engine Controller SKODA FABIA 1.2 TDI DELPHI 28281647 03P906021K DCM3.7
Which models is the 28281647 controller compatible with?
The 28281647 controller is compatible with SKODA FABIA models equipped with a 1.2 TDI engine, ensuring optimal vehicle performance.
What is the role of the 03P906021K engine controller?
The 03P906021K engine controller manages the engine's operation, controlling parameters such as fuel injection and ignition, which are crucial for efficiency and driving economy.
What are the symptoms of a faulty DCM3.7 controller?
Symptoms of a faulty DCM3.7 controller may include starting issues, uneven idle operation, and increased fuel consumption.
Where can you find the 03P906021K number on the controller?
The 03P906021K number can be found on the controller's casing, usually on a label with a barcode or an embossed number.
Does the 28281647 controller require programming after installation?
After installation, the 28281647 controller may require programming to adapt to the vehicle's specific parameters. We provide technical support and fast shipping.
