The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ABS pump Isuzu Grafter ADVICS 898250132 1338002740
Vendors's code: 898250132
Product code: 1338002740
Barcode:
Code 39:
ISBN:
1 951,22 zł
Price
1 951,22 zł
2 400,00 zł
Price
2 400,00 zł
Ask about the product
ABS pump Isuzu Grafter ADVICS 898250132 1338002740
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Will ABS pump 898250132 fit your Isuzu?
Used ABS pump with control unit, number 898250132, inspected before sale. Matched by the numbers on the block and sticker.
Isuzu Grafter ABS pump 898250132: hydraulic module with control unit
The hydraulic block and control unit of this ABS pump form a single module that works with the wheel speed sensors in Isuzu Grafter cars. You will find number 898250132 on the label, and the full set of numbers is given in the description below. According to the listing, the pump comes from the Isuzu Grafter model.
Part number 898250132 and related numbers
Below are the numbers as they appear on the labels, together with the single-string form used in catalogues:
- 898250132, original Isuzu number,
- 1338002740, additional number from the listing.
Compare the numbers with the original pump in your car, and if any of them differs, write to us before buying.
When an ABS module needs replacing
- valve or pump motor faults are stored in the control unit memory,
- the ABS activates for no reason during normal braking,
- brake fluid leaks from the hydraulic block, which requires immediate action,
- on a slippery surface the wheels lock up noticeably sooner than they used to.
Before buying a module, read the fault codes with a diagnostic tester. A faulty wheel speed sensor or its wiring can cause the same symptoms, and in that case replacing the pump will not help. After replacement the fault codes usually need to be cleared, and if the brake lines have been disconnected, the system must be bled.
Questions and answers
| Where do I find number 898250132 on my pump? |
|---|
| The numbers are stamped or printed on the aluminium hydraulic block, and the control unit has a separate sticker. Take a close-up photo of both places in good light. |
| Are the pump and the control unit sold separately? |
| In this listing they are a single module: a hydraulic block with the pump and valves, with the control unit attached to it. |
| Can I send a photo for a compatibility check? |
| Yes. Contact us and send a photo of the numbers on your original pump, and we will help you check whether this module will fit. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Want to check before you buy? Send a photo of the block and sticker on your ABS pump and we will check that the numbers match.
