The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine Controller VOLKSWAGEN 03G906021MJ 03G906021AB 0281014045
Vendors's code: 03G906021AB
Product code: 3661-72243
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller VOLKSWAGEN 03G906021MJ 03G906021AB 0281014045
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£23.03
-
shipping
(Poland)
from
£23.03
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
VOLKSWAGEN ECU ENGINE CONTROLLER 03G906021MJ 03G906021AB 0281014045
The Ecu engine controller 03G906021MJ, 03G906021AB and 0281014045 is a tested and properly matched component that ensures stable and correct operation of the power unit in Volkswagen vehicles.
What is the function of the Ecu engine controller 03G906021MJ in Volkswagen vehicles?
The Ecu engine controller identified by part numbers 03G906021MJ and 0281014045 manages engine operation in Volkswagen vehicles. The module analyzes sensor data and controls fuel injection, dosing and engine operating parameters, ensuring stable performance and driving comfort.
Which vehicles use this Ecu engine controller?
This Ecu engine controller was installed in selected Volkswagen models with diesel engines. Exact compatibility depends on engine version, model year and equipment, therefore ECU number or VIN verification is recommended before purchase.
How can I check if the Ecu engine controller fits my vehicle?
The most reliable method is to compare the numbers on the installed unit. If 03G906021AB, 03G906021MJ or 0281014045 is present, the Ecu engine controller is compatible with your vehicle. If in doubt, please contact us before ordering.
Why does this Ecu engine controller have multiple part numbers?
Different numbers come from the vehicle manufacturer and the electronics supplier. The references 03G906021MJ, 03G906021AB and 0281014045 all refer to the same Ecu engine controller and differ only in notation.
How should I search for a Volkswagen Ecu engine controller online?
The best results come from entering a full reference number, such as 03G906021MJ. It is also worth checking 0281014045, as listings may use different identifiers for the same unit.
Are additional procedures required after replacing the Ecu engine controller?
Yes — after installation, the Ecu engine controller usually requires adaptation, coding or cloning to work properly with the immobilizer and other vehicle systems. This is a standard ECU replacement procedure.
Which Ecu engine controller versions are available in our store?
We offer two Ecu engine controller variants: a locked version and a virgin (logged-out) version. Please review the variant descriptions to choose the best option for your needs.
What is the order processing time?
If the Ecu engine controller 03G906021MJ / 0281014045 is in stock, shipping is usually completed within 24–48 hours. Current processing times are always listed in the product description.
What should I do if the ordered Ecu engine controller is not suitable?
In this case, please contact us with the part number and vehicle details. We will help you select the correct Ecu engine controller or suggest a compatible alternative.
