A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
FGP 55190069 WJ ECU engine controller Opel Corsa C 1.3 CDTI Z13DT Y13DT Magneti Marelli MJD6JO.C2
Vendors's code: 55190069 WJ
Product code: 7087
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
FGP 55190069 WJ ECU engine controller Opel Corsa C 1.3 CDTI Z13DT Y13DT Magneti Marelli MJD6JO.C2
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£23.19
-
shipping
(Poland)
from
£23.19
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Control unit for Corsa C 1.3 CDTI – Magneti Marelli MJD 6JO.C2 / FGP 55190069 WJ
This engine control unit for Opel Corsa C with 1.3 CDTI engines is available in several variants: locked, logged out as clean VIRGIN, or as a Plug&Play set with immobiliser.
FAQ – engine controller FGP 55190069 WJ Magneti Marelli MJD6JO.C2
Does FGP 55190069 WJ fit Opel Corsa C 1.3 CDTI?
Yes, this engine control unit is used in Opel Corsa C models with Z13DT and Y13DT diesel engines. The most important step is confirming the number on your module label.
I have a unit marked MJD 6JO.C2 – is it the same type?
Yes. The designations MJD6JO.C2, MJD6JOC2 or MJD6J0C2 refer to the same family of Magneti Marelli devices.
Are numbers 71600.023.08, 71600.023.04 and 71600.023.06 interchangeable?
These references are related to the same controller used in Corsa C. In practice, the main number FGP 55190069 WJ is decisive.
What versions can I choose when buying?
Different variants are available: locked unit for data cloning, prepared VIRGIN unit for adaptation and complete Plug&Play set with immobiliser and transponders.
What does logged-out version mean in MJD6JO.C2?
The module is cleared of previous data. After installation, standard adaptation can be performed using appropriate diagnostic equipment.
What is included in immobiliser set for 55190069?
You receive matched security system components. Installation is Plug&Play without coding.
My mechanic looks for 7160002308 – is it correct?
Yes, this number belongs to the same Magneti Marelli platform and is often found together with FGP55190069.
Is programming required after replacement?
If you choose VIRGIN version – yes, immobiliser adaptation is required. With full start kit the vehicle starts without additional procedures.
How to confirm compatibility?
Compare full markings from old module: Magneti Marelli, MJD 6JO.C2 family and FGP number.
What symptoms indicate controller failure?
No start, diagnostic communication issues, immobiliser errors or irregular engine operation.
