A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller FIAT 500 1.3 Multijet 55253513 MJD8F3X1 – VIRGIN Plug & Play Ready for installation
Vendors's code:
Product code: 0603-12595
Barcode:
Code 39:
ISBN:
£219.84
Price
£219.84
Regular price:
£219.84
0%
£270.40
Price
£270.40
Regular price:
£270.40
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller FIAT 500 1.3 Multijet 55253513 MJD8F3X1 – VIRGIN Plug & Play Ready for installation
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£23.18
-
shipping
(Poland)
from
£23.18
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
55253513 MJD8F3X1 – ECU ENGINE CONTROLLER FIAT 500 1.3 Multijet (MAGNETI MARELLI) VIRGIN Plug & Play
Original MAGNETI MARELLI MJD 8F3.X1 ECU ENGINE CONTROLLER for FIAT 500 1.3 Multijet, part number 55253513, in VIRGIN version – ready for programming or preparation as Plug & Play according to VIN.
FAQ – / 55253513 / MJD8F3X1 FIAT 500 1.3 Multijet
Does engine control unit 55253513 fit every FIAT 500 1.3 Multijet?
Model 55253513 was used in selected versions of the 1.3 MJT (Multijet) engine. Compatibility should be confirmed by VIN number or by comparing the MJD8F3X1 marking with the original engine control unit installed in the vehicle.
What does it mean that MJD8F3X1 is in VIRGIN version?
The VIRGIN version means that the immobilizer memory has been cleared and the unit is not assigned to any specific vehicle. This engine control unit 55253513 requires adaptation in the vehicle (PROXI alignment / programming via diagnostic tool).
Can engine control unit 55253513 MJD8F3X1 be prepared as Plug & Play?
Yes, it is possible to program engine control unit 55253513 based on data from the original unit (EEPROM + FLASH), so after installation no additional coding will be required.
For which production years is MJD8F3X1 suitable?
The MAGNETI MARELLI MJD 8F3.X1 unit was used in FIAT 500 1.3 Multijet in selected production years (Euro 4 / Euro 5). Final compatibility is confirmed by VIN number and matching part number 55253513.
After installing engine control unit 55253513, do injectors need coding?
In the VIRGIN version, full configuration may be required, including immobilizer adaptation and possible synchronization of engine parameters using a suitable diagnostic device.
How can I check if my FIAT 500 has MJD8F3X1 engine control unit?
You should read the number from the label of the old engine control unit or verify vehicle equipment by VIN number. The marking MAGNETI MARELLI MJD 8F3.X1 and number 55253513 must match the original unit.
Is engine control unit 55253513 new or refurbished?
The offered MJD8F3X1 unit is technically tested, checked before shipping and prepared in VIRGIN version, ready for proper configuration in the vehicle.
