A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller BMW BOSCH 0281011120 / DDE 7794650
Vendors's code: DDE 7794650
Product code: 9B53-97600
Barcode:
Code 39:
ISBN:
£157.42
Price
£157.42
Regular price:
£157.42
0%
£193.62
Price
£193.62
Regular price:
£193.62
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller BMW BOSCH 0281011120 / DDE 7794650
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£23.23
-
shipping
(Poland)
from
£23.23
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU ENGINE CONTROLLER BMW BOSCH 0281011120 / DDE 7794650
The control module BOSCH 0281011120 with designation DDE 7794650 is dedicated to selected BMW diesel engine models. It is responsible for fuel injection control, engine operating parameters, and proper communication with the vehicle’s systems. A proven solution in case of failure of the original unit – compatibility guaranteed by part number.
FAQ – ECU Engine Controller BMW BOSCH 0281011120 / DDE 7794650
What is the function of the 0281011120 controller in BMW?
The ECU Engine controller with part number 0281011120 is responsible for electronic management of the BMW diesel engine. The module controls, among others, fuel injection quantity, boost parameters, and communication with sensors, ensuring proper engine dynamics and stable operation.
What is DDE 7794650 and does it refer to the same module?
The designation 7794650 is a number used in the BMW system for the DDE controller. In practice, it refers to the same engine computer as BOSCH 0281011120 – the difference results from dual numbering by the vehicle manufacturer and the electronics manufacturer.
In which BMW models is controller 7794650 used?
The DDE module with number 7794650 was installed in selected BMW diesel engine versions. Its application depends on the production year and engine variant, therefore compatibility should be verified via VIN or by comparing numbers with the current ECU before purchase.
How can I check if 0281011120 fits my car?
The easiest method is to read the number from the housing of the currently installed controller. If 0281011120 or DDE 7794650 is present, it indicates compatibility in terms of catalog number. In case of doubt, it is recommended to provide the VIN for verification.
Why does the controller have both a BOSCH number and a BMW number?
The number 0281011120 is assigned by the electronics manufacturer (Bosch), while 7794650 is the number used by BMW. Both identifiers refer to the same type of engine controller and are used interchangeably in listings.
How to best search for this part online?
For effective searching, it is recommended to use full designations such as 0281011120 BMW or DDE 7794650. Using both numbers increases the chance of finding the correct controller for a specific engine version.
Is adaptation required after installing controller 7794650?
Yes, after replacing the engine controller, synchronization with the immobilizer and configuration for the specific vehicle is usually required. This is a standard procedure when installing a used or virgin DDE module.
What should I do if 0281011120 turns out to be incompatible?
In such a case, contact the seller and provide the current ECU number and vehicle details. This will allow selecting the correct BMW controller or a compatible solution for the engine version.
