A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller MITSUBISHI CARISMA 1.8 MR578146 E2T68488 H
Vendors's code: E2T68488
Product code: MR578146
Barcode:
Code 39:
ISBN:
813,01 zł
Price
813,01 zł
Regular price:
813,01 zł
0%
1 000,00 zł
Price
1 000,00 zł
Regular price:
1 000,00 zł
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller MITSUBISHI CARISMA 1.8 MR578146 E2T68488 H
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU ENGINE CONTROLLER MITSUBISHI CARISMA 1.8 MR578146 E2T68488 H
Tested ECU Engine controller for Mitsubishi Carisma 1.8 with reference numbers MR578146 and E2T68488 (identifier H), with warranty and fast shipping straight to the customer.
ECU Engine controller MITSUBISHI CARISMA 1.8 MR578146 E2T68488 H
Which Mitsubishi Carisma 1.8 versions does the MR578146 E2T68488 ECU fit?
The Mitsubishi Carisma 1.8 ECU Engine controller MR578146 E2T68488 should be matched primarily by the numbers on your original unit. This is the safest method, because similar-looking ECUs can still differ by version and configuration.
Before you buy, compare the markings on your ECU: MR578146 and E2T68488. If your label also shows the letter H, it's worth matching that identifier too.
What does the Mitsubishi Carisma 1.8 engine ECU E2T68488 control?
The Mitsubishi Carisma 1.8 ECU E2T68488 manages engine operation based on sensor inputs and works together with the vehicle's electronics during everyday driving.
The MR578146 ECU supports stable running, smooth acceleration and consistent engine response under load.
What symptoms can a faulty Mitsubishi Carisma ECU MR578146 cause?
A faulty Mitsubishi Carisma engine ECU MR578146 may cause starting problems, rough running, loss of power or diagnostic fault codes. In some cases, communication issues with the ECU can also appear.
The MR578146 / E2T68488 ECU (H) is checked and tested before shipping, so you receive a verified product with warranty and fast delivery.
Why are part numbers MR578146 and E2T68488 important when choosing an ECU for Carisma?
Part numbers MR578146 and E2T68488 help you select the correct ECU Engine controller for a specific Mitsubishi Carisma 1.8 version. Even similar modules can have different software or internal settings, which affects operation after installation.
To reduce mismatch risk, compare all markings on your original unit, including the letter H if present.
Does the Mitsubishi Carisma 1.8 ECU MR578146 require programming?
Depending on the vehicle version, the Mitsubishi Carisma 1.8 ECU MR578146 E2T68488 may require adaptation or programming after installation, especially if it is linked to the immobiliser and security systems.
Matching reference numbers makes installation easier and helps ensure correct operation after replacement.
