Vendors's code: E2T65775
Product code: MD328466
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Tested ECU engine controller for the Mitsubishi Lancer and Colt 1.3, part numbers MD328466 and E2T65775 6118 – covered by warranty with fast shipping.
The ECU engine controller MITSUBISHI LANCER COLT 1.3 MD328466 E2T65775 6118 was installed in the Mitsubishi Lancer and Mitsubishi Colt equipped with the 1.3 petrol engine (engine code 4G13). The module manages engine operation and ensures correct communication with all other electronic systems on board.
The control unit E2T65775 is found in both the Mitsubishi Lancer and Colt with the 1.3 engine, so it is advisable to verify every number on the original module before ordering.
The ECU module E2T65775 6118 in the Mitsubishi Colt 1.3 controls fuel injection, ignition timing, sensor data processing and communication with the remaining electronic systems. It is one of the most critical electronic components in the vehicle.
The controller MD328466 keeps the 4G13 engine running optimally in all conditions – from daily commutes to longer motorway journeys.
A defective engine controller MD328466 in the Mitsubishi Lancer 1.3 typically causes starting difficulties, unstable idle, sudden power loss or an illuminated check-engine light. In some cases the diagnostic tool may also fail to establish communication with the ECU module.
Every E2T65775 6118 unit is thoroughly tested before dispatch, so the customer can count on a fully working product backed by warranty and fast delivery.
The number E2T65775 is usually found on the metal casing or label of the engine controller fitted in the Mitsubishi Colt or Lancer 1.3. The catalogue number MD328466 and the additional marking 6118 should also be visible nearby.
Carefully comparing every marking on the original module with the numbers on the replacement unit helps avoid compatibility issues after fitting.
Depending on the model year and trim of the Mitsubishi Lancer or Colt 1.3, the engine controller MD328466 E2T65775 6118 may require adaptation or coding after installation. This mainly concerns the immobiliser and key pairing.
Matching the numbers MD328466 and E2T65775 with the original module greatly speeds up the entire replacement process and helps get the car running again after the repair.
Cookies and related technologies enable the website to function properly and help us tailor the offer to your needs. You can accept our use of all these files and go to the store or adjust the use of files to your preferences by selecting the "Customize consents" option.
Here you can specify your preferences regarding our use of cookies.
These files are necessary for the operation of our website, so you cannot disable them.
These files enable you to use other functions of the website (other than those necessary for its operation). Enabling them will give you access to the full functionality of the website.
These files allow us to analyze our online store, which may contribute to its better functioning and adaptation to the needs of Users.
Thanks to these files, we can conduct marketing activities.
