Vendors's code: 8631A369
Product code: A1351508179
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Tested ECU engine controller for the Smart ForFour and Mitsubishi Colt 1.3, part numbers A1351508179 and 8631A369 E6T42487 H8ZE – covered by warranty with fast shipping.
The ECU engine controller SMART MITSUBISHI COLT 1.3 A1351508179 8631A369 E6T42487 H8ZE was fitted in the Smart ForFour and Mitsubishi Colt (Z30 series) equipped with a 1.3 petrol engine. Both vehicles share a common platform, so the same ECU module fits either brand.
The control unit A1351508179 (Smart/Mercedes catalogue number, also written as A 135 150 81 79) also carries the Mitsubishi designation 8631A369 and the Mitsubishi Electric number E6T42487 H8ZE, ensuring a precise match for the specific vehicle variant.
The ECU module E6T42487 H8ZE in the Smart ForFour and Mitsubishi Colt 1.3 oversees the key operating parameters of the petrol engine. The controller monitors crankshaft position, temperature and lambda sensor signals, optimising fuel dosing and ignition timing in all driving conditions.
The engine controller 8631A369 maintains low fuel consumption while ensuring smooth 1.3 engine performance in both city traffic and on longer journeys.
A defective engine controller with number 8631A369 or A1351508179 may result in a non-starting vehicle, the engine entering limp mode, jerking while driving or an illuminated check-engine light. A common sign is also a lack of communication with diagnostic tools via the OBD2 port.
Every ECU module E6T42487 H8ZE is thoroughly tested before dispatch, so the customer receives a verified product backed by warranty and fast delivery.
The number A1351508179 is usually found on the metal casing or label of the engine controller fitted in the Smart ForFour or Mitsubishi Colt. The Mitsubishi catalogue number 8631A369 and the Mitsubishi Electric designation E6T42487 H8ZE should also be visible nearby.
Carefully comparing all markings – A1351508179, 8631A369 and E6T42487 H8ZE – on the original module helps prevent compatibility issues after the ECU replacement.
In most cases the Smart Mitsubishi Colt 1.3 engine controller A1351508179 8631A369 E6T42487 H8ZE requires synchronisation with the immobiliser and vehicle key after installation. This is a standard procedure to ensure vehicle security.
Matching the designations A1351508179 and 8631A369 with the original module greatly simplifies the adaptation process and helps get the car back to full operation quickly.
Cookies and related technologies enable the website to function properly and help us tailor the offer to your needs. You can accept our use of all these files and go to the store or adjust the use of files to your preferences by selecting the "Customize consents" option.
Here you can specify your preferences regarding our use of cookies.
These files are necessary for the operation of our website, so you cannot disable them.
These files enable you to use other functions of the website (other than those necessary for its operation). Enabling them will give you access to the full functionality of the website.
These files allow us to analyze our online store, which may contribute to its better functioning and adaptation to the needs of Users.
Thanks to these files, we can conduct marketing activities.
