A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
Engine control module Audi 0261207934 8E0909518AA ME7.5
Vendors's code:
Product code: E797-556E9
Barcode:
Code 39:
ISBN:
£187.61
Price
£187.61
£230.76
Price
£230.76
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine control module Audi 0261207934 8E0909518AA ME7.5
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£23.08
-
shipping
(Poland)
from
£23.08
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control module Audi 0261207934 8E0909518AA ME7.5
The engine control module with part numbers 0261207934 and 8E0909518AA ME7.5 for Audi is a proven component responsible for engine operation, available in either locked or unlocked variants.
Does the 0261207934 engine control unit fit Audi?
The engine control unit 0261207934 with designation 8E0909518AA MED7.5 is used in Audi models, especially with the 1.8T engine. If your current ECU has the same number, it indicates very high compatibility.
What does 8E0909518AA mean in the 0261207934 ECU?
The 8E0909518AA is the Audi part number that allows precise matching of the ECU to a specific vehicle model.
What does MED7.5 mean in the 0261207934 ECU?
MED7.5 is a type of ECU used in 1.8T petrol engines, managing fuel injection and ignition.
Does the 0261207934 ECU require programming?
The ECU may require adaptation. Locked and unlocked versions are available.
How to check if 8E0909518AA ECU will fit?
Compare the number on your ECU. Matching numbers indicate compatibility.
Why is the 0261207934 number important?
It uniquely identifies the ECU and helps avoid mistakes.
Is the MED7.5 0261207934 ECU ready to install?
It depends on the variant; some require configuration.
Symptoms of a faulty 0261207934 ECU
Starting problems, diagnostic errors, or unstable engine operation.
Does 8E0909518AA appear in other ECUs?
Yes, but combined with 0261207934 it refers to a specific MED7.5 version.
What to consider when buying 0261207934 ECU?
Check the number, condition, and choose the correct variant.
