A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
Engine control module Audi 0261S06181 8K2907115AE
Vendors's code:
Product code: 0DE9-501FF
Barcode:
Code 39:
ISBN:
£218.87
Price
£218.87
£269.22
Price
£269.22
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine control module Audi 0261S06181 8K2907115AE
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£23.08
-
shipping
(Poland)
from
£23.08
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control module Audi 0261S06181 8K2907115AE
The engine control module with part numbers 0261S06181 and 8K2907115AE for Audi is a proven component for managing engine operation, available in either locked or unlocked variants.
Does the 0261S06181 engine control unit fit Audi?
The 0261S06181 ECU with designation 8K2907115AE is an original control unit used in Audi models with the 2.0 TFSI engine, particularly A4 and A5 from around 2008–2013. If your current ECU has the same numbers, it is highly likely to be compatible.
What does 8K2907115AE mean in the 0261S06181 ECU?
8K2907115AE is the Audi catalog number for this ECU. Together with Bosch number 0261S06181, it allows precise identification of the correct unit, minimizing the risk of errors when purchasing.
What type of ECU is 0261S06181?
0261S06181 is a Bosch unit from the MED17.1 family, used in modern gasoline engines with direct fuel injection. This designation refers to electronics responsible for engine management.
Does the 0261S06181 ECU require programming?
The 0261S06181 8K2907115AE may require coding/programming for the specific vehicle. Variants available include locked, unlocked, or ready-to-program units, so check the product description before purchase.
How to check if the 8K2907115AE ECU will fit?
The best method is to compare the number 8K2907115AE or 0261S06181 with your current ECU. Matching numbers ensure the highest certainty of compatibility.
Why is 0261S06181 important when choosing?
0261S06181 is a Bosch-specific number that helps avoid mistakes when purchasing an engine control unit. It is the most reliable way to select the correct part without guessing based on the car model alone.
Is the MED17.1 0261S06181 ready to install?
It depends on the chosen unit – it may be ready for immediate installation or require additional coding/programming. Always check the variant description in the offer.
Symptoms of a faulty 8K2907115AE ECU
A defective 0261S06181 ECU can cause starting problems, diagnostic errors, uneven engine operation, or loss of communication with the diagnostic computer. In such cases, replacement is usually necessary.
What to check when buying a 0261S06181 ECU?
Ensure the part number matches 0261S06181 or 8K2907115AE, check the technical condition, and select the correct variant (locked, unlocked, or ready-to-install) for proper operation after installation.
