A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
Engine control module Audi 0281012269 4F0907401B
Vendors's code:
Product code: 88BF-93109
Barcode:
Code 39:
ISBN:
813,01 zł
Price
813,01 zł
1 000,00 zł
Price
1 000,00 zł
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine control module Audi 0281012269 4F0907401B
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control module Audi 0281012269 4F0907401B
The engine control module with part numbers 0281012269 and 4F0907401B for Audi is a proven component for managing engine operation, available in either locked or unlocked variants.
Does the 0281012269 engine control unit fit Audi?
The engine control unit with the number 0281012269 and designation 4F0907401B is an original control unit used in Audi vehicles, mainly in models like Audi A6 C6 3.0 TDI from around 2005–2008. If your current ECU has these numbers, you can be highly confident that the part will fit.
What does the number 4F0907401B mean in the 0281012269 ECU?
The number 4F0907401B is the Audi/VW catalog code for the ECU, which, combined with Bosch's 0281012269 number, uniquely identifies the engine control unit. This helps avoid mistakes when selecting parts for your vehicle.
Does the 0281012269 engine computer require programming?
The 0281012269 4F0907401B ECU often requires adaptation to the specific car after installation. Many offers provide units in locked or logged-out versions – the latter are prepared for programming in the vehicle. Check the offer description before purchase.
How to check if the 4F0907401B ECU will fit?
The best way is to compare the numbers 0281012269 or 4F0907401B with those on your current ECU. Matching numbers is the most reliable way to avoid mistakes and ensure the correct ECU is installed in your vehicle.
Why is the 0281012269 number key when choosing an ECU?
The 0281012269 number is Bosch’s exact designation, which eliminates ambiguity and helps select the right part for a specific Audi diesel engine. It prevents compatibility issues.
Is the 0281012269 4F0907401B ECU ready for installation?
It depends on the variant you choose. The ECU may be available as locked or logged-out — the latter requires PIN/immobilizer code programming and adaptation in a workshop before installation.
What are the symptoms of a faulty 0281012269 ECU?
A faulty 0281012269 engine control unit can cause loss of communication with the diagnostic computer, fuel injection errors, starting problems, or ECU memory faults. In such cases, replacement or repair is often necessary.
Does the number 4F0907401B occur with other Bosch numbers?
Yes, the 4F0907401B designation may coexist with other Bosch numbers, such as 0281012270 or 0281012279, which also describe ECU versions used in similar vehicles.
What to consider when buying the 0281012269 ECU?
The most important is matching the numbers 0281012269 or 4F0907401B to your vehicle, checking the technical condition, and selecting the appropriate variant (locked, logged-out, or ready for installation). This ensures the ECU works correctly after installation.
