Skip to main content
English €
English €
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English €
English €
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Throttle Body Toyota Avensis Corolla 220300D010

  • Part Type Throttle body
  • Vehicle Make and Model Toyota Avensis, Corolla
  • Manufacturer Part Number 220300D010
  • Warranty 6-month warranty
  • Condition Used, working, in good condition
  • Testing & Inspection Device thoroughly inspected and tested by a certified technician
ORYGINAL
with VAT without VAT
Price €100.00
Availability:
product-availability-module In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Ask about the product
Shipping from €30.00 - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type Throttle body
  • Vehicle Make and Model Toyota Avensis, Corolla
  • Manufacturer Part Number 220300D010
  • Warranty 6-month warranty
  • Condition Used, working, in good condition
  • Testing & Inspection Device thoroughly inspected and tested by a certified technician

Does the 220300D010 throttle body fit your car?

This is a used, working throttle body with part number 220300D010, for: Toyota Avensis, Corolla. To confirm the fit, compare the number with the label on the throttle body in your car.

Go to full description

Throttle Body 220300D010 – Toyota Avensis, Corolla

The 220300D010 throttle body controls the air flow in the engine intake system. In electronic versions, the throttle plate position is controlled by the engine control unit. According to the product data, it fits: Toyota Avensis, Corolla.

Part numbers to compare

  • 220300D010

The same number – 220300D010 – should appear on the label of the throttle body in your car. The model name alone (Toyota Avensis, Corolla) is not enough – throttle bodies with other numbers were also fitted to these cars.

Common throttle body faults

When the throttle body in a Toyota starts to fail, the most common signs are:

  • carbon deposits – rough idle, engine stalling,
  • worn throttle position sensor – jerking, fluctuating revs, fault code stored in the engine control unit,
  • in electronic throttle bodies: failed motor or gear drive – limp mode, loss of power, engine warning light.

When measurements or fault codes confirm the problem and cleaning has no effect, the throttle body is replaced with one carrying the same number. After replacement, many cars need an adaptation in the engine control unit.

Questions and answers

How do I check that the 220300D010 throttle body fits my car?
Compare the number 220300D010 with the label of the throttle body fitted to your car (Toyota Avensis, Corolla).
Does the throttle body need to be adapted (relearned) after replacement?
In many cars, yes – the engine control unit has to learn the positions of the new throttle body. This is done with a diagnostic tool or according to the vehicle manufacturer's procedure.
What condition is this throttle body in?
It is a used part in good working condition. The warranty period is shown in the product specification table.

Not sure if this throttle body fits your car? Send us the number from the label on your part and we will check compatibility before shipping.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Water-damaged ABS pump control module or a burnt-out one - what next?

    A water-damaged or burnt-out ABS pump control module most often lights up the dashboard like a 'Christmas tree' (ABS, ESP and the red brake warning light), leaves the diagnostic tool unable to communicate with the ABS module, makes the pump motor run non-stop or stops the speedometer working. Water usually gets into the module when the scuttle panel drains are blocked, after the engine bay has been cleaned with a pressure washer or after driving through a deep puddle, while a burnout is most often caused by a short circuit or a voltage spike. Below we describe the symptoms, what to do straight away and why drying or repairing such a module rarely gives lasting results.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more
  • How to test an ABS module and pump - failure symptoms and checks

    The most common symptom of a faulty ABS pump or ABS module is an ABS warning light that stays on after the engine starts, often together with the ESP light. The brakes still work, but without ABS the wheels can lock under hard braking. To test an ABS module, start by reading the fault codes with a diagnostic tool that can talk to the ABS unit, then check the power supply, the earth and the wheel speed sensors. Only when all of these are fine is the module itself usually to blame.

    Read more