A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS ASR PML control unit Mercedes S-Class W140 W210 0265109050 0185459132
Vendors's code: 0265109050
Product code: 2CF5-667A3
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Is this Mercedes S-Class W140 W210 unit the right one for your car?
This is a used, working ABS ASR PML control unit for the Mercedes S-Class W140 W210 - numbers 0 265 109 050 / 0265109050; 018 545 91 32 / 0185459132. Before buying, compare the numbers with the label on the unit in your car.
ABS ASR PML control unit Mercedes S-Class W140 W210
The ABS ASR PML control unit is an electronic module of the brake system that analyses wheel sensor signals and controls brake pressure. This listing is for: Mercedes S-Class W140 W210 (1991-1998). The part is used, working and in good condition.
Numbers to compare
- 0 265 109 050 / 0265109050 - manufacturer number (Bosch)
- 018 545 91 32 / 0185459132 - Mercedes-Benz number (OEM)
Application according to the listing
- Mercedes S-Class W140 W210 - model
- 1991-1998 - year
- Bosch - manufacturer
What the control unit does
The unit receives the wheel speed sensor signals and compares them. When it detects that a wheel is starting to lock, it controls the valves in the brake system to reduce pressure and keep the car steerable.
Fitment
Compare the number 0 265 109 050 in full with the number on your unit. Different versions were fitted to the same models, so the number decides, not the model and year alone.
Signs of a faulty control unit
- the ABS light is on right after starting the engine,
- the ABS and brake lights stay on after switching on the ignition,
- traction control switches off,
- the unit does not communicate with the scan tool.
Before buying a unit, check the fuse, power supply, earth and wheel speed sensors - a damaged harness or sensor causes similar symptoms.
Questions and answers
| How do I check whether the control unit will fit my car? |
|---|
| Compare the model, year, engine and the numbers on the unit fitted in your car with those in the description. You can also send us a photo. |
| What should I check on delivery? |
| Check that the numbers match the description and that the connector and housing show no cracks or corrosion. |
| What does "used, working" mean? |
| We sell it as a used part, working and in good condition, with a 6-month warranty. |
Send fitment questions to contact@auto24parts.com - give the model, year and the number on the unit.