A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS control unit Audi A4 A6 0265108005 4D0907379D
Vendors's code: 0265108005
Product code: 94BB-989DF
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Is this Audi A4 A6 unit the right one for your car?
This is a used, working ABS control unit for the Audi A4 A6 - numbers 0 265 108 005 / 0265108005; 4D0 907 379 D / 4D0907379D. Before buying, compare the numbers with the label on the unit in your car.
ABS control unit Audi A4 A6
This ABS control unit is intended for: Audi A4 A6 (1995-1999). It is a used part, working and in good technical condition.
Numbers to compare
- 0 265 108 005 / 0265108005 - manufacturer number (Bosch)
- 4D0 907 379 D / 4D0907379D - VAG group number (OEM)
Application according to the listing
- Audi A4 A6 - model
- 1995-1999 - year
- Bosch - manufacturer
What the control unit does
In many models the module needs coding or adaptation after replacement. Check this for your model before ordering.
Fitment
We have several units for this model with different numbers. The label number and year decide, not the model name.
Signs of a faulty control unit
- the ABS and brake lights stay on after switching on the ignition,
- no wheel speed reading,
- the car reports sensor faults even though the sensors are fine,
- the unit overheats or resets.
The braking system is critical for safety - have the ABS checked at a garage after replacement.
Questions and answers
| What does "used, working" mean? |
|---|
| We sell it as a used part, working and in good condition, with a 6-month warranty. |
| Is the hydraulic unit (ABS pump) included? |
| This listing is for the control unit described in the title. If you also need the pump, write to us before buying and we will confirm exactly what is included. |
| Can a control unit with a different number fit too? |
| Sometimes, but we do not assume listings are interchangeable. Compare all numbers with the label on your unit or ask us. |
Send fitment questions to contact@auto24parts.com - give the model, year and the number on the unit.