A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS control unit Mercedes W124 W126 0265101020 0055455132
Vendors's code: 0265101020
Product code: 808C-3271E
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Control unit with number 0265101020 - is it the right part?
This is a used, working ABS control unit for the Mercedes W124 W126 - numbers 0 265 101 020 / 0265101020; 005 545 51 32 / 0055455132. Before buying, compare the numbers with the label on the unit in your car.
ABS control unit Mercedes W124 W126
The ABS control unit is an electronic module of the brake system that analyses wheel sensor signals and controls brake pressure. This listing is for: Mercedes W124 W126. The part is used, working and in good condition.
Numbers to compare
- 0 265 101 020 / 0265101020 - manufacturer number (Bosch)
- 005 545 51 32 / 0055455132 - Mercedes-Benz number (OEM)
Application according to the listing
- Mercedes W124 W126 - model
- Bosch - manufacturer
What the control unit does
In older cars the ABS unit is often a separate module, while in newer ones it is combined with the hydraulic unit. This listing is for the unit described in the title; we will confirm what is included on request.
Fitment
We also stock other units for this model with different numbers. Choose by the label number, not by the model alone.
Signs of a faulty control unit
- an ABS fault appears after a battery change,
- unstable voltage at the module,
- the brake and ABS warning lights come on together,
- the brakes work, but without ABS assistance.
Remember that the unit may need coding or adaptation after replacement - check this for your model.
Questions and answers
| What does "used, working" mean? |
|---|
| We sell it as a used part, working and in good condition, with a 6-month warranty. |
| Can I fit a control unit from a different equipment version? |
| We do not assume so. Units differ in functions (ABS, ESP, ASR) and software, so compare the numbers and your car's version. |
| What should I check on delivery? |
| Check that the numbers match the description and that the connector and housing show no cracks or corrosion. |
Not sure? Send a photo of your control unit to contact@auto24parts.com and we will check it for you.