A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS ESP BAS control unit Mercedes W168 A-Class 0265109477 0295454232
Vendors's code: 0265109477
Product code: 7F61-6325C
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Does this ABS control unit fit the Mercedes W168 A-Class?
This is a used, working ABS ESP BAS control unit for the Mercedes W168 A-Class - numbers 0 265 109 477 / 0265109477; 0295454232. Before buying, compare the numbers with the label on the unit in your car.
ABS ESP BAS control unit Mercedes W168 A-Class
For the Mercedes W168 A-Class (1999-2001) we offer a used unit that manages the ABS; match it by the numbers in the list. It is working and in good condition.
Numbers to compare
- 0 265 109 477 / 0265109477 - manufacturer number (Bosch)
- 0295454232 - Mercedes-Benz number (OEM)
- 029 545 42 32 Q01 / 0295454232Q01 - additional part number
Application according to the listing
- Mercedes W168 A-Class - model
- 1999-2001 - year
- 140 160 170 190 CDI - engine according to the listing
- Bosch - manufacturer
What the control unit does
The unit's electronics consist of a processor, valve driver stages and sensor input circuits. Each of these can fail independently, which causes different symptoms.
Fitment
We have several units for this model with different numbers. The label number and year decide, not the model name.
Signs of a faulty control unit
- the ABS light is on right after starting the engine,
- the scan tool cannot connect to the module,
- the speedometer shows wrong values (if it uses the ABS signal),
- the system works only intermittently.
Before buying a unit, check the fuse, power supply, earth and wheel speed sensors - a damaged harness or sensor causes similar symptoms.
Questions and answers
| What does "used, working" mean? |
|---|
| We sell it as a used part, working and in good condition, with a 6-month warranty. |
| Do you also sell connectors or ABS sensors? |
| This listing is for the control unit only. You will find other parts in the other shop categories, or ask us about availability. |
| What should I check on delivery? |
| Check that the numbers match the description and that the connector and housing show no cracks or corrosion. |
For questions about fitment, write to contact@auto24parts.com and give the number on the label.