A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump BMW E90 ATE 6784765 6784766 10061336721
Vendors's code: 6784766
Product code: 10061336721
Barcode:
Code 39:
ISBN:
€325.20
Price
€325.20
€400.00
Price
€400.00
Ask about the product
ABS pump BMW E90 ATE 6784765 6784766 10061336721
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
When is ABS pump 6784765 the right choice for your BMW E90?
Used ABS pump with control unit, number 6784765, inspected before sale. Matched by the numbers on the block and sticker.
Is ABS pump 6784765 the right part for your BMW?
This is a used original ABS pump with a control unit for BMW E90 cars: an aluminium hydraulic block with valves and a pump motor, with the electronics bolted to it. The main number is 6784765, and the other numbers from the labels are listed below. According to the listing, the pump comes from the BMW E90 model.
Part number 6784765 and related numbers
You will find the numbers on the labels, while catalogues list them as a single string:
- 6784765, BMW number in short form, without the group prefix,
- 6784766, BMW number in short form, without the group prefix,
- 10.0613-3672.1 (catalogue format: 10061336721), additional number from the listing.
Matching by number is more reliable than matching by car model. Compare all the numbers and ask us if any of them does not match.
Symptoms of a faulty ABS pump or control unit
- the ABS warning light comes on after the engine is started and stays on,
- the pump motor switches on at unusual moments or runs louder than usual,
- brake fluid leaks from the hydraulic block, which requires immediate action,
- the ABS warning light comes on together with the stability control warning light.
Before buying a module, read the fault codes with a diagnostic tester. A faulty wheel speed sensor or its wiring can cause the same symptoms, and in that case replacing the pump will not help. After replacement the fault codes usually need to be cleared, and if the brake lines have been disconnected, the system must be bled.
Questions and answers
| Where do I find number 6784765 on my pump? |
|---|
| The numbers are stamped or printed on the aluminium hydraulic block, and the control unit has a separate sticker. Take a close-up photo of both places in good light. |
| Are the pump and the control unit sold separately? |
| In this listing they are a single module: a hydraulic block with the pump and valves, with the control unit attached to it. |
| Does a lit ABS warning light always mean a faulty pump? |
| No. Read the fault codes first, because the cause may be a wheel sensor, its wiring or too low a supply voltage. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Not sure about the match? Send us a photo of the numbers on your ABS pump and we will check whether this module will fit.
