A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump BMW X5 Bosch 6870761 6874801 0265254430 0265956331
Vendors's code: 6874801
Product code: 6870761
Barcode:
Code 39:
ISBN:
£185.87
Price
£185.87
£228.61
Price
£228.61
Ask about the product
ABS pump BMW X5 Bosch 6870761 6874801 0265254430 0265956331
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£22.86
-
shipping
(Poland)
from
£22.86
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Will ABS pump 6870761 fit your BMW?
Used ABS pump with control unit, number 6870761, inspected before sale. Matched by the numbers on the block and sticker.
How to identify ABS pump 6870761 for your BMW X5
The hydraulic block and control unit of this ABS pump form a single module that works with the wheel speed sensors in BMW X5 cars. You will find number 6870761 on the label, and the full set of numbers is given in the description below. According to the listing, the pump comes from the BMW X5 model.
Where to find the numbers on an ABS pump
You will find the numbers on the labels, while catalogues list them as a single string:
- 6874801, BMW number in short form, without the group prefix,
- 6870761, BMW number in short form, without the group prefix,
- 0 265 254 430 (catalogue format: 0265254430), hydraulic block manufacturer's number,
- 0 265 956 331 (catalogue format: 0265956331), control unit number.
The full numbers matter, including their endings. If in doubt, send us a photo of your pump.
What ABS problems can point to
- the ABS warning light comes on after the engine is started and stays on,
- the brake pedal pulses or feels uneven for no obvious reason,
- the pump motor switches on at unusual moments or runs louder than usual,
- the ABS warning light comes on together with the stability control warning light.
First check the wheel sensors, their wiring and the supply voltage. Only a fault code pointing to the module justifies replacing the pump. After fitting, clear the fault codes and, if necessary, bleed the brake system.
Questions and answers
| What is the difference between numbers 6870761 and 6874801? |
|---|
| The module carries several numbers, because it is identified both by the car brand and by the manufacturer of the block and control unit. When matching the part, compare all the numbers. |
| Does a lit ABS warning light always mean a faulty pump? |
| No. Read the fault codes first, because the cause may be a wheel sensor, its wiring or too low a supply voltage. |
| Who makes this module? |
| The module is made by Bosch. The manufacturer's name does not change the numbers you should use to match the part. |
| What condition is this ABS module in? |
| It is an original recycled part in good condition, checked by us. Warranty details are in the product features table. |
Want to be certain? Send us the numbers from the block and sticker on your ABS pump, and together we will check whether this part will fit.
