Skip to main content
English zł
English zł
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English zł
English zł
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

ABS pump and control module Chrysler Jeep 04779975AK

  • Part Type ABS pump with control module
  • Vehicle Make and Model Chrysler Jeep
  • OEM Part Number 04779975AK
  • Warranty 6-month warranty
  • Testing & Inspection Device thoroughly inspected and tested by a certified technician
  • Condition Used, working, in good condition
ORYGINAL
with VAT without VAT
Price 1 400,00 zł
Availability:
product-availability-module In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Ask about the product
Shipping from 120,00 zł - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type ABS pump with control module
  • Vehicle Make and Model Chrysler Jeep
  • OEM Part Number 04779975AK
  • Warranty 6-month warranty
  • Testing & Inspection Device thoroughly inspected and tested by a certified technician
  • Condition Used, working, in good condition

One number, 04779975AK - is it enough to match an ABS unit?

A used, working, genuine unit: an ABS pump and control unit from a Chrysler or Jeep car. The listing carries one part number (OEM): 04779975AK. We do not state the model - matching is done by number.

Go to full description

Chrysler, Jeep - ABS pump with control unit 04779975AK

This listing is simple: one number, one unit. The part number (OEM) is 04779975AK, and we describe this ABS pump with control unit by that number alone. There is no ATE number or other references, and no model or year either. The unit is used, working and genuine, from a Chrysler or Jeep car.

Number in the listing

  • 04779975AK - OEM part number: 04779975AK

Since there is only one number, compare it exactly, including the letter ending. If your part shows a version with an extra prefix or a different ending, ask us about compatibility.

What usually prompts a replacement

Reasons why an ABS unit ends up being replaced:

  • control unit damage detected by the scanner,
  • an ABS warning light that cannot be cleared,
  • the pump does not switch on during the activation test.

Before replacing the unit, read out the fault codes and check the wheel sensors and wiring harness. After fitting, bleed the brake system; if necessary, configure the module with a scanner, as in many cars this is a requirement.

Briefly about this listing

How do I know it is the right unit if there is only one number?
Compare it with your number 04779975AK. If it is identical, that is the right basis for matching; if there are differences, write to us.
Which Chrysler or Jeep model is it?
We do not state the model. We know the unit comes from a car of one of those brands, and the number settles the rest.
Does the listing cover a complete set with pump and control unit?
Yes, it is an ABS pump together with a control unit, described by a single part number (OEM).
Is the part in working order?
Yes, it is used, working and genuine. You can check the warranty terms in the product features table.

Prefer to be sure before buying? Send the number of your part or your VIN, and we will check it against 04779975AK.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Water-damaged ABS pump control module or a burnt-out one - what next?

    A water-damaged or burnt-out ABS pump control module most often lights up the dashboard like a 'Christmas tree' (ABS, ESP and the red brake warning light), leaves the diagnostic tool unable to communicate with the ABS module, makes the pump motor run non-stop or stops the speedometer working. Water usually gets into the module when the scuttle panel drains are blocked, after the engine bay has been cleaned with a pressure washer or after driving through a deep puddle, while a burnout is most often caused by a short circuit or a voltage spike. Below we describe the symptoms, what to do straight away and why drying or repairing such a module rarely gives lasting results.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more
  • How to test an ABS module and pump - failure symptoms and checks

    The most common symptom of a faulty ABS pump or ABS module is an ABS warning light that stays on after the engine starts, often together with the ESP light. The brakes still work, but without ABS the wheels can lock under hard braking. To test an ABS module, start by reading the fault codes with a diagnostic tool that can talk to the ABS unit, then check the power supply, the earth and the wheel speed sensors. Only when all of these are fine is the module itself usually to blame.

    Read more