A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump and control module Citroen Peugeot 9806891780 10022003774
Vendors's code: 9806891780
Product code: 10091511793
Barcode:
Code 39:
ISBN:
€162.60
Price
€162.60
€200.00
Price
€200.00
Ask about the product
ABS pump and control module Citroen Peugeot 9806891780 10022003774
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Citroen Peugeot - is this the right ABS pump for your car?
This is a used, working ABS pump with control module for the Citroen Peugeot - numbers 9806891780; 10.0220-0377.4 / 10022003774. Before buying, compare the numbers with the label on the module in your car.
ABS pump and control module Citroen Peugeot
An ABS pump with control module is one of the key active safety components. This listing applies to: Citroen Peugeot; the part is used, working and in good condition.
Numbers to compare
- 9806891780 - part number (OEM)
- 10.0220-0377.4 / 10022003774 - ABS pump number (ATE)
- 10.0915-1179.3 / 10091511793 - ABS control module number (ATE)
Application according to the listing
- Citroen Peugeot - model
- ATE - manufacturer
How an ABS pump with control module works
The valves in the hydraulic block open and close many times per second, and the control module monitors their operation continuously. A failure of any of these parts turns on the ABS warning light.
Matching
For this model we offer several pumps with different numbers. The number on the label decides, not the model name alone. The ABS pump is part of the safety system, so it is worth comparing the numbers carefully before buying. A mismatched version may not work with the car's sensors or wiring.
Symptoms of a faulty ABS pump
- valve fault codes appear,
- the ABS works unevenly,
- the warning light stays on even after a sensor replacement,
- the module stops responding after moisture gets in.
If the brake system has been opened, it must be bled after fitting, often using a diagnostic tool that controls the ABS valves.
Questions and answers
| What condition is this part in? |
|---|
| It is a used, working part in good condition. The condition is also given in the product features. |
| Where can I find the number on the module? |
| You will usually find the numbers on the label or housing of the module, visible after removing it from the car. If you cannot read them, send us a photo. |
| Does the brake fluid need replacing after the pump is fitted? |
| The system has to be bled after the pump is replaced anyway, so it is a good moment to check the fluid and replace it if it is old. |
Write to contact@auto24parts.com with the model, year and the number from your pump - we will check the fit.
