A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump Ford Bosch EB3C2C405AG 0265243911 0265956179
Vendors's code: 0265956179
Product code: 8647-940BE
Barcode:
Code 39:
ISBN:
$327.86
Price
$327.86
$403.27
Price
$403.27
Ask about the product
ABS pump Ford Bosch EB3C2C405AG 0265243911 0265956179
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
$30.24
-
shipping
(Poland)
from
$30.24
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Will ABS pump EB3C2C405AG fit your Ford?
Used ABS pump with control unit, number EB3C2C405AG, inspected before sale. Matched by the numbers on the block and sticker.
Used Ford ABS pump with number EB3C2C405AG
The hydraulic block and control unit of this ABS pump form a single module that works with the wheel speed sensors in Ford cars. You will find number EB3C2C405AG on the label, and the full set of numbers is given in the description below. The listing does not state the car model or year, so we do not give them here and match the part by its numbers.
Numbers and markings on the ABS pump
Below are the numbers as they appear on the labels, together with the single-string form used in catalogues:
- EB3C-2C405-AG (catalogue format: EB3C2C405AG), original Ford number,
- 0 265 243 911 (catalogue format: 0265243911), hydraulic block manufacturer's number,
- 0 265 956 179 (catalogue format: 0265956179), control unit number.
Compare the numbers with the original pump in your car, and if any of them differs, write to us before buying.
What can point to an ABS pump failure
- the ABS warning light comes on after the engine is started and stays on,
- the brake pedal pulses or feels uneven for no obvious reason,
- the ABS activates for no reason during normal braking,
- the ABS switches itself off shortly after the engine is started.
Before buying a module, read the fault codes with a diagnostic tester. A faulty wheel speed sensor or its wiring can cause the same symptoms, and in that case replacing the pump will not help. After replacement the fault codes usually need to be cleared, and if the brake lines have been disconnected, the system must be bled.
Questions and answers
| Which car model does this pump fit? |
|---|
| The listing does not state a model or year, so confirm compatibility with the number from the original pump in your car, or send us a photo of it. |
| Does a lit ABS warning light always mean a faulty pump? |
| No. Read the fault codes first, because the cause may be a wheel sensor, its wiring or too low a supply voltage. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| What condition is this pump in? |
| It is a used original part, inspected before sale. You will find the warranty period in the product features table. |
Want to be certain? Send us the numbers from the block and sticker on your ABS pump, and together we will check whether this part will fit.
