A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump and control module Kia Stinger 58920J5240 BE6008W502
Vendors's code: 58920J5240
Product code: BE6008W502
Barcode:
Code 39:
ISBN:
€162.60
Price
€162.60
€200.00
Price
€200.00
In stock
Ask about the product
ABS pump and control module Kia Stinger 58920J5240 BE6008W502
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Does this ABS pump fit the Kia Stinger?
This is a used, working ABS pump with control module for the Kia Stinger - numbers 58920-J5240 / 58920J5240; BE6008W502. Before buying, compare the numbers with the label on the module in your car.
ABS pump and control module Kia Stinger
An ABS pump with electronics helps you keep control of the car during hard braking. The unit offered applies to: Kia Stinger; it is used, working and in good condition.
Numbers to compare
- 58920-J5240 / 58920J5240 - part number (OEM)
- BE6008W502 - part number (OEM)
Application according to the listing
- Kia Stinger - model
How an ABS pump with control module works
The valves in the hydraulic block open and close many times per second, and the control module monitors their operation continuously. A failure of any of these parts turns on the ABS warning light.
Matching
Compare number 58920-J5240 in full with the number on your pump. Different versions were fitted to the same models, so the number decides the fit, not the model alone. The fit is decided first of all by the part number, and only then by the model and year, because different modules were used within one model.
Symptoms of a faulty ABS pump
- the ABS and brake warning lights do not go out after switching on the ignition,
- no wheel speed reading,
- the car reports sensor faults even though the sensors work,
- the module overheats or resets.
Check the level and condition of the brake fluid; old or contaminated fluid accelerates wear of the valves in the hydraulic unit.
Questions and answers
| What condition is this part in? |
|---|
| It is a used, working part in good condition. The condition is also given in the product features. |
| Can I fit a pump from a different equipment version? |
| We do not assume so. Modules differ in functions (ABS, ESP, ASR) and software, so compare the numbers and the version of your car. |
| Do the brakes need bleeding after replacement? |
| Yes, once the brake system has been opened it must be bled. In many cars this is done with a diagnostic tool that activates the ABS valves. |
Not sure? Write to contact@auto24parts.com and we will help you choose the right ABS pump for your car.
