A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump Mercedes Bosch A1764310200 0265254537 0265956003
Vendors's code: 0265254537
Product code: A1764310200
Barcode:
Code 39:
ISBN:
€284.55
Price
€284.55
€350.00
Price
€350.00
Ask about the product
ABS pump Mercedes Bosch A1764310200 0265254537 0265956003
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Will ABS pump A1764310200 fit your Mercedes?
ABS pump A1764310200 complete with control unit, used and inspected. Compare the numbers with the original in your car.
Mercedes ABS pump A1764310200: hydraulic module with control unit
ABS module A1764310200 is used and has been inspected before sale. It is intended for Mercedes cars, but whether it fits is decided by comparing the numbers with the original part in your car. The listing does not state the car model or year, so we do not give them here and match the part by its numbers.
Part number A1764310200 and related numbers
The numbers as written on the labels and as a single string, the way catalogues list them:
- A 176 431 02 00 (catalogue format: A1764310200), Mercedes number stamped on the hydraulic block,
- 0 265 254 537 (catalogue format: 0265254537), hydraulic block manufacturer's number,
- 0 265 956 003 (catalogue format: 0265956003), control unit number.
Compare the numbers with the original pump in your car, and if any of them differs, write to us before buying.
When an ABS module needs replacing
- the ABS warning light comes on after the engine is started and stays on,
- the pump motor switches on at unusual moments or runs louder than usual,
- the ABS warning light comes on together with the stability control warning light,
- the ABS switches itself off shortly after the engine is started.
ABS faults should not be ignored, because without anti-lock protection the car brakes less well on wet or slippery roads. Diagnosis and fitting are best left to a garage with a suitable scanner.
Questions and answers
| Where do I find number A1764310200 on my pump? |
|---|
| The numbers are stamped or printed on the aluminium hydraulic block, and the control unit has a separate sticker. Take a close-up photo of both places in good light. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| Who makes this module? |
| The module is made by Bosch. The manufacturer's name does not change the numbers you should use to match the part. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Not sure about the match? Send us a photo of the numbers on your ABS pump and we will check whether this module will fit.
