Skip to main content
In English +48 792 797 344 Polski +48 501 409 435 +48 32 201 72 96 En Español +34 63 727 27 85 contact@auto24parts.com
English zł
English zł
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English zł
English zł
Wishlist
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

ABS pump and control module Volkswagen 5N0614109AG
  • ABS pump and control module Volkswagen 5N0614109AG
  • ABS pump and control module Volkswagen 5N0614109AG - photo 2
  • Part Type ABS pump with control module
  • Vehicle Make and Model Volkswagen
  • OEM Part Number 5N0 614 109 AG / 5N0614109AG
  • Warranty 6-month warranty
  • Testing & Inspection Device thoroughly inspected and tested by a certified technician
  • Condition Used, working, in good condition
Trw
with VAT without VAT
Price 700,00 zł
PLN GBP EUR USD
Availability:
product-availability-module In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Shipping time: 48 godzin
Ask about the product
Shipping from 120,00 zł - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price

PRODUCT DETAILS

  • Part Type ABS pump with control module
  • Vehicle Make and Model Volkswagen
  • OEM Part Number 5N0 614 109 AG / 5N0614109AG
  • Warranty 6-month warranty
  • Testing & Inspection Device thoroughly inspected and tested by a certified technician
  • Condition Used, working, in good condition

ABS pump number 5N0614109AG - is this the right part?

This is a used, working ABS pump with control module for the Volkswagen - numbers 5N0 614 109 AG / 5N0614109AG. Before buying, compare the numbers with the label on the module in your car.

Go to full description

ABS pump and control module Volkswagen

If the ABS warning light is on in your Volkswagen or the brake system reports faults, the pump with control module may be the cause. We sell a used, working unit in good condition.

Numbers to compare

  • 5N0 614 109 AG / 5N0614109AG - part number (OEM)

Application according to the listing

  • Volkswagen - model

How an ABS pump with control module works

The valves in the hydraulic block open and close many times per second, and the control module monitors their operation continuously. A failure of any of these parts turns on the ABS warning light.

Matching

We also offer other pumps for this model with different numbers. Choose by the number on the module, not by the model alone. The brake system is critical for safety, so fitting is best left to a workshop that will bleed the brakes and check ABS operation.

Symptoms of a faulty ABS pump

  • the ABS warning light is on,
  • ABS stops working during braking,
  • the control module does not communicate with the diagnostic tool,
  • sometimes the ESP or traction control light comes on as well.

It is worth reading the fault codes with a diagnostic tool first, because some ABS faults come from wheel sensors or wiring, not from the hydraulic unit itself.

Questions and answers

What condition is this part in?
It is a used, working part in good condition. Please send any questions about its condition to us before buying.
Do the brakes need bleeding after replacement?
Yes, once the brake system has been opened it must be bled. In many cars this is done with a diagnostic tool that activates the ABS valves.
Do you also sell ABS sensors or connectors?
This listing covers only the pump with control module. You will find additional parts in the other categories of the shop, or ask us about availability.

Send questions about compatibility to contact@auto24parts.com - state the model, year and the number from the module.

Latest Articles
See All

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more

  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more

  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more

  • Water-damaged ABS pump control module or a burnt-out one - what next?

    A water-damaged or burnt-out ABS pump control module most often lights up the dashboard like a 'Christmas tree' (ABS, ESP and the red brake warning light), leaves the diagnostic tool unable to communicate with the ABS module, makes the pump motor run non-stop or stops the speedometer working. Water usually gets into the module when the scuttle panel drains are blocked, after the engine bay has been cleaned with a pressure washer or after driving through a deep puddle, while a burnout is most often caused by a short circuit or a voltage spike. Below we describe the symptoms, what to do straight away and why drying or repairing such a module rarely gives lasting results.

    Read more

  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more

  • How to test an ABS module and pump - failure symptoms and checks

    The most common symptom of a faulty ABS pump or ABS module is an ABS warning light that stays on after the engine starts, often together with the ESP light. The brakes still work, but without ABS the wheels can lock under hard braking. To test an ABS module, start by reading the fault codes with a diagnostic tool that can talk to the ABS unit, then check the power supply, the earth and the wheel speed sensors. Only when all of these are fine is the module itself usually to blame.

    Read more