A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump Mazda GJ6E437A0 4614E0299
Vendors's code: 4614E0299
Product code: GJ6E437A0
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
€100.00
Price
€100.00
Ask about the product
ABS pump Mazda GJ6E437A0 4614E0299
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
What does number GJ6E437A0 on an ABS pump mean?
Used ABS pump with control unit, number GJ6E437A0, inspected before sale. Matched by the numbers on the block and sticker.
Is ABS pump GJ6E437A0 the right part for your Mazda?
ABS pump GJ6E437A0 for Mazda is a used original module that regulates brake pressure when a wheel starts to lock up. It is matched by the numbers on its labels, not by the car model alone. The listing does not state the car model or year, so we do not give them here and match the part by its numbers.
Where to find the numbers on an ABS pump
The numbers as written on the labels and as a single string, the way catalogues list them:
- GJ6E437A0, original Mazda number,
- 4614E0299, additional number from the listing.
Compare the numbers with the original pump in your car, and if any of them differs, write to us before buying.
What can point to an ABS pump failure
- the brake pedal pulses or feels uneven for no obvious reason,
- valve or pump motor faults are stored in the control unit memory,
- the pump motor switches on at unusual moments or runs louder than usual,
- brake fluid leaks from the hydraulic block, which requires immediate action.
It is worth reading the fault codes and checking the sensor wiring before replacement. Fitting and bleeding the brake system are usually carried out by a garage with the right equipment.
Questions and answers
| What is the difference between numbers GJ6E437A0 and 4614E0299? |
|---|
| The module carries several numbers, because it is identified both by the car brand and by the manufacturer of the block and control unit. When matching the part, compare all the numbers. |
| Which car model does this pump fit? |
| The listing does not state a model or year, so confirm compatibility with the number from the original pump in your car, or send us a photo of it. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Not sure about the match? Send us a photo of the numbers on your ABS pump and we will check whether this module will fit.
