Skip to main content
English €
English €
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English €
English €
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Airbag clock spring Opel Astra H 13198906 XC

  • Part Type Airbag clock spring
  • Vehicle Make and Model Opel Astra H
  • Manufacturer Valeo
  • Manufacturer Part Number 203773
  • OEM Part Number 13198906 XC / 13198906XC
  • Condition Used part
GM
with VAT without VAT
Price €40.00
Availability:
In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Shipping time: 24 h
Ask about the product
Shipping from €30.00 - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type Airbag clock spring
  • Vehicle Make and Model Opel Astra H
  • Manufacturer Valeo
  • Manufacturer Part Number 203773
  • OEM Part Number 13198906 XC / 13198906XC
  • Condition Used part

Does airbag clock spring 13198906 XC fit your Opel Astra H?

This is a used airbag clock spring with number 13198906 XC, used in the Opel Astra H. Before buying, compare the number with the label on your clock spring.

Go to full description

Airbag clock spring Opel Astra H 13198906 XC

This used airbag clock spring carries number 13198906 XC. It comes from an Opel, and in the listing we matched it to the Opel Astra H. This Astra H clock spring was made by Valeo. The housing shows a GM number with a letter code and a separate Valeo number.

Numbers on the label

  • 13198906 XC / 13198906XC - OEM number (GM)
  • 203773 - Valeo manufacturer number

Models in the listing

  • Opel Astra H

A clock spring is a housing with a coiled flat cable. It keeps the airbag and steering wheel buttons connected to the wiring, even at full lock.

Typical fault symptoms

  • the airbag warning light comes on, often after turning the wheel,
  • the horn does not work,
  • you hear clicking or rubbing when turning the wheel.

Fitting

The clock spring is fitted with the wheels pointing straight ahead and in the centre position. If it is set wrongly, it can tear at the first full turn. Before work, disconnect the battery and wait the time specified by the car maker. Set the wheels straight and fit the clock spring in its centre position, using the marks on the housing.

Questions and answers

What condition is the clock spring in?
It is a used part from a dismantled car. If you need details of its condition, ask us before buying.
How do I check that it fits?
Compare the number on your clock spring housing with the number in the listing, then the model and year of your car.
Will the airbag light go out after replacement?
If the clock spring was the cause, usually yes, but a stored fault sometimes has to be cleared with a diagnostic tool.

Questions about fitment? Write to contact@auto24parts.com and give the number from your clock spring.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Water-damaged ABS pump control module or a burnt-out one - what next?

    A water-damaged or burnt-out ABS pump control module most often lights up the dashboard like a 'Christmas tree' (ABS, ESP and the red brake warning light), leaves the diagnostic tool unable to communicate with the ABS module, makes the pump motor run non-stop or stops the speedometer working. Water usually gets into the module when the scuttle panel drains are blocked, after the engine bay has been cleaned with a pressure washer or after driving through a deep puddle, while a burnout is most often caused by a short circuit or a voltage spike. Below we describe the symptoms, what to do straight away and why drying or repairing such a module rarely gives lasting results.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more
  • How to test an ABS module and pump - failure symptoms and checks

    The most common symptom of a faulty ABS pump or ABS module is an ABS warning light that stays on after the engine starts, often together with the ESP light. The brakes still work, but without ABS the wheels can lock under hard braking. To test an ABS module, start by reading the fault codes with a diagnostic tool that can talk to the ABS unit, then check the power supply, the earth and the wheel speed sensors. Only when all of these are fine is the module itself usually to blame.

    Read more