Skip to main content
English $
English $
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English $
English $
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Airbag clock spring Opel Vectra C Signum 13162135 DM

  • Part Type Airbag clock spring
  • Vehicle Make and Model Opel Vectra C Signum
  • OEM Part Number 13162135 DM / 13162135DM
  • Condition Used part
with VAT without VAT
Price $30.11
Availability:
In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Ask about the product
Shipping from $30.11 - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type Airbag clock spring
  • Vehicle Make and Model Opel Vectra C Signum
  • OEM Part Number 13162135 DM / 13162135DM
  • Condition Used part

Clock spring 13162135 DM - is it the right one for your car?

We offer a used airbag clock spring 13162135 DM for the Opel Vectra C and Opel Signum. The number on the housing decides the fit, so check it before you order.

Go to full description

Airbag clock spring Opel Vectra C Signum 13162135 DM

This used airbag clock spring carries number 13162135 DM. It comes from an Opel, and in the listing we matched it to the Opel Vectra C and Opel Signum. In the Vectra C and Signum the clock spring is part of the module under the steering wheel, and versions differ by the letter code next to the GM number.

Markings on the housing

  • 13162135 DM / 13162135DM - OEM number (GM)

Fitment according to the listing

  • Opel Vectra C
  • Opel Signum

The clock spring connects the driver airbag, horn and steering wheel buttons to the car wiring. Inside there is a wound flat cable that lets the wheel turn without breaking the connection.

Typical fault symptoms

  • the horn does not work,
  • steering wheel buttons work intermittently or not at all,
  • the airbag module stores a driver airbag circuit fault.

Fitting tips

The airbag system contains pyrotechnic charges, so fitting is best left to a workshop. After replacement the fault may need clearing in the airbag module with a diagnostic tool. Before work, disconnect the battery and wait the time specified by the car maker. Set the wheels straight and fit the clock spring in its centre position, using the marks on the housing.

Frequently asked questions

What condition is the clock spring in?
It is a used part from a dismantled car. If you need details of its condition, ask us before buying.
How do I check that it fits?
Compare the number on your clock spring housing with the number in the listing, then the model and year of your car.
Does the clock spring need centring before fitting?
Yes. It is fitted in the centre position with the wheels pointing straight ahead.

Questions about fitment? Write to contact@auto24parts.com and give the number from your clock spring.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more