The engine control unit (often referred to as ECU or ECM) is the most important electronic module in every modern vehicle. It acts as the main computer managing the operation of the power unit, analyzing signals from numerous sensors in real-time. It is responsible for precise fuel dosing, ignition timing, boost pressure, and the operation of exhaust gas treatment systems. When this crucial component fails, normal operation of the car becomes impossible. When faced with electronic problems, many drivers consider complicated diagnostics, circuit testing, and attempting to repair integrated circuits. In practice, the fastest, safest, and most cost-effective solution is to replace the damaged component with a fully functional, original used part from the aftermarket.
Engine Control Unit Alfa Romeo MiTo 1.3 JTDM 55258958 MJD 8F3.M2
Vendors's code:
Product code: BADA-213C9
Barcode:
Code 39:
ISBN:
€325.20
Price
€325.20
Regular price:
€325.20
0%
€400.00
Price
€400.00
Regular price:
€400.00
0%
In stock
Wybierz wariant produktu:
Individual variants may differ in price
Warranty
Attention : Depending on the type of engine controller and car model, not every variant from the list below is available.
To choose the correct variant for your car and model engine controller please contact with us :
1.Locked: This variant is intended for workshops that have specialized equipment and knowledge.
Engine computer removed from a car intended for recycling with data saved from the previous car and immobilizer. To use this controller it is required to unlock it and then perform the programming procedure. For this purpose, it is necessary to use specialized diagnostic equipment for electronics.
2.Unlocked: There are many variants of the possible unlock device , so please contact us before purchasing because, depending on the type and model of the car or controller itself make some unlocking options not possible.
The controller can be prepared for assembly by our electronics in various ways: the list below
a) ECU with read PIN code (CAR PASS) - Required programming by diagnostic device. After the assmbly of the ecu to the car you need to reset that controller by typing in the pin code, and then performing the procedure of programming the immobilizer to your car
b) Cleaned Ecu out of the data of the previus car (VIRGIN). The ECU is reset to factory settings, prepared as clean. After installation in the car, it requires programming by using a specialized diagnostic device (STANDARD Unlocking of most of our ECUs if not specified the unlocking form)
c)Plug & Play (IMMO OFF) - excluded immobilizer, it has removed the safety codes from the ecu. Once its connected ecu to the car the engine runs and it does not require any programming, but it does not have the immobilizer function. - No need additional programming
d) Plug & Play (AUTO PROGRAMMING) - after assembly the ecu in the car, ECU will automatically program itself to your car. Does not require any programming
e) Plug & Play (CLON) - a cloned controller prepared for installation in a car without the need for programming. This device is copied 1 to 1 from the old device and the data is transferred to another properly working computer by our electrician service technician
Have to send us the damaged driver from which the data will be transferred to another, properly working computer.
Broken ecu HAS to have working communication with the car or diagnostic device , without proper communication Security code cant be cloned.
3.Complete: Plug & Play complete set ecu with immobilizer and all elements needed to start the vehicle without need for additional programming. Have to replace all the elements sent by us in your car.
Attention :
Delivery time depends on the selected variant: if the unlocked version is selected,
the unlocking service takes an additional time of around 1-2 business days
Ask about the product
Engine Control Unit Alfa Romeo MiTo 1.3 JTDM 55258958 MJD 8F3.M2
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control unit Alfa Romeo MiTo 1.3 JTDM 55258958 MJD 8F3.M2
Engine control unit with part numbers 55258958 and MJD 8F3.M2 (MJD8F3M2) dedicated to Alfa Romeo MiTo 1.3 JTDM – available in locked or unlocked version, check the description before purchase.
Does the Alfa Romeo MiTo 1.3 JTDM MJD engine control unit 55258958 8F3.M2 fit my car?
The engine control unit with numbers 55258958 and 8F3.M2 is designed for the Alfa Romeo MiTo 1.3 JTDM MJD. Checking these markings on your current unit ensures that the new ECU will be compatible with your car.
Both part numbers – 55258958 and 8F3.M2 – help confirm the correct ECU model before purchase.
What does part number 8F3.M2 mean in the engine control unit?
The number 8F3.M2 identifies a specific ECU used in the Alfa Romeo MiTo 1.3 JTDM MJD. This number helps match the correct replacement and avoid compatibility issues.
Units with numbers 55258958 and 8F3.M2 often appear together, as both refer to the same control unit.
Why check numbers 55258958 and 8F3.M2 before purchase?
Checking part numbers is key to properly matching the ECU. Numbers 55258958 and 8F3.M2 ensure the engine control unit will work correctly in your car and help avoid a wrong purchase.
Is the engine control unit 8F3.M2 / 55258958 available in different variants?
Yes, in our store the ECU with numbers 8F3.M2 and 55258958 is available in two variants: locked or unlocked. It’s worth reviewing the variant descriptions before purchase to select the proper unit for your vehicle.
How to identify the ECU by numbers 55258958 and 8F3.M2?
The easiest way is to check the markings on your old ECU. If the numbers 55258958 or 8F3.M2 appear, it confirms this is the exact model used in the Alfa Romeo MiTo 1.3 JTDM MJD.
Do numbers 55258958 and 8F3.M2 refer to the same engine control unit?
Yes, a single ECU often has two manufacturer numbers. 55258958 and 8F3.M2 may refer to the same unit, so it’s always recommended to check both numbers before purchasing.
