A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Comfort control module Jaguar S-TYPE YW4T13B524BA
Vendors's code: YW4T13B524BA
Product code: YW4T13B524BA
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
€100.00
Price
€100.00
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Comfort control module Jaguar S-TYPE YW4T13B524BA
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Part number YW4T13B524BA - is it the right choice?
We sell a used, working part (comfort control module) for Jaguar S-TYPE with numbers YW4T-13B524-BA / YW4T13B524BA. Before buying, compare the numbers with the label on the part in your car.
Comfort control module Jaguar S-TYPE
This module (comfort control module) is intended for: Jaguar S-TYPE (2000). This is a used, working part in good technical condition.
How this part works
It is an electronic node of the body wiring: it receives signals from switches and sensors and then activates consumers such as lights, locks or ventilation.
Part numbers to check
- YW4T-13B524-BA / YW4T13B524BA - part number
Symptoms of a fault
- electric windows respond with a delay or not at all,
- interior lights or indicators work incorrectly,
- the central locking or locking signal does not work,
- communication errors appear on the dashboard.
Remember that the module may need coding or adaptation after replacement - check this for your model.
Application according to the listing
- Jaguar S-TYPE - model
- 2000 - year
- 3.0 V6 - engine according to the listing
Matching by numbers
Our range also includes other parts for this model with different numbers. Choose by the number on the label, not by the model and year alone.
Questions and answers
| Do you also sell connectors or wiring? |
|---|
| This listing covers only the part described in the title. You will find other items in the remaining shop categories, or ask us about availability. |
| Is the part new? |
| This is a used, working part in good condition. You will find the warranty period in the product features table. |
| What if I cannot see my number in the description? |
| Write to us and give the number from your part. We will check whether we have it in stock, also in another listing. |
Send a photo of your part or its number to contact@auto24parts.com and we will confirm whether this listing fits.
