A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Comfort module Chrysler Voyager 2.8 CRD P04692247AA
Vendors's code: P04692247AA
Product code: 04692247AA
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
€100.00
Price
€100.00
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Comfort module Chrysler Voyager 2.8 CRD P04692247AA
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Does comfort module P04692247AA fit the Chrysler Voyager 2.8 CRD?
Yes, if the number on your module is P04692247AA or 04692247AA. This is a used, fully working comfort module for the Chrysler Voyager with the 2.8 CRD engine. You confirm the fit with the number on the sticker.
Comfort module Chrysler Voyager 2.8 CRD P04692247AA
The comfort module in the Chrysler Voyager handles body electronics and works together with the car’s other modules. It is not an engine ECU. This one, for the Chrysler Voyager with the 2.8 CRD engine, carries number P04692247AA, written without the P prefix as 04692247AA. The part is used, fully working and inspected before sale.
Numbers to compare
- P04692247AA – part number on the sticker
- 04692247AA – the same number without the P prefix
Compatibility is determined by the number on the sticker, not by the car model alone. Different versions of the module were fitted to the same models, so compare the whole number.
Signs of a faulty module
- a body function does not work although the switch is fine,
- the module heats up or smells burnt,
- random fault codes appear in the diagnostic memory,
- the car does not go into full sleep mode.
It is worth reading the fault codes first, because some body faults come from switches or wiring rather than from the module itself.
Questions and answers
| Is the P04692247AA an engine ECU? |
|---|
| No. It is a comfort module, part of the body electronics. The engine ECU is a separate part with a different number. |
| Is 04692247AA the same part? |
| Yes. It is the same number written without the P prefix. |
| Does it need coding after fitting? |
| That depends on the version and the car. A used module comes from another vehicle, so it usually needs adaptation or coding after fitting. Write to us before buying and we will confirm what is needed. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Want to check before you buy? Send a photo of the sticker on your module to contact@auto24parts.com and we will check that the number matches. See also: vehicle control modules and electronic car parts.
