A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller MITSUBISHI GT3000 FTO 3.0 MD305409 E2T63871
Vendors's code: E2T63871
Product code: MD305409
Barcode:
Code 39:
ISBN:
1 138,21 zł
Price
1 138,21 zł
Regular price:
1 138,21 zł
0%
1 400,00 zł
Price
1 400,00 zł
Regular price:
1 400,00 zł
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller MITSUBISHI GT3000 FTO 3.0 MD305409 E2T63871
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU ENGINE CONTROLLER MITSUBISHI GT3000 FTO 3.0 MD305409 E2T63871
Tested ECU Engine controller for Mitsubishi GT3000 and FTO 3.0 with reference numbers MD305409 and E2T63871, with warranty and fast shipping straight to the customer.
ECU Engine controller MITSUBISHI GT3000 FTO 3.0 MD305409 E2T63871
Which Mitsubishi models does the MD305409 E2T63871 engine ECU fit?
The Mitsubishi ECU Engine controller MD305409 E2T63871 should be matched primarily by the part numbers on your original unit. This is the safest method, because similar-looking ECUs can still differ by version and configuration.
These references are associated with Mitsubishi GT3000 and Mitsubishi FTO 3.0 applications (always confirm by checking the labels on your current ECU).
What does the Mitsubishi engine ECU E2T63871 control?
The Mitsubishi ECU E2T63871 manages engine operation based on sensor inputs and works together with the vehicle’s electronics during everyday driving.
The MD305409 controller supports stable running, smooth acceleration and consistent engine response under load.
What symptoms can a faulty Mitsubishi ECU MD305409 cause?
A faulty Mitsubishi engine ECU MD305409 may cause starting issues, rough running, loss of power or diagnostic fault codes. In some cases, communication problems with diagnostics can also appear.
The MD305409 / E2T63871 ECU is checked and tested before shipping, so you receive a verified product with warranty and fast delivery.
Why are part numbers MD305409 and E2T63871 important when choosing a Mitsubishi ECU?
Part numbers MD305409 and E2T63871 help you select the correct ECU Engine controller for a specific Mitsubishi configuration. Even modules that look alike may have different software or internal settings, which affects operation after installation.
Matching the reference numbers is the simplest way to reduce the risk of ordering the wrong unit.
Does the Mitsubishi ECU MD305409 E2T63871 require programming?
Depending on the vehicle version, the Mitsubishi ECU MD305409 E2T63871 may require adaptation or programming after installation, especially if it is linked to the immobiliser and vehicle security systems.
Correct reference numbers make installation easier and help the vehicle operate properly after replacement.
