Vendors's code: 237101F720
Product code: BF50-408E1
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Ecu engine controller 0261206502, also known as 237101F720 and 23710-1F720, is a matched part for Nissan Micra 1.4 that supports even and stable engine operation in everyday use.
The Ecu engine controller 0261206502 is responsible for the correct operation of the 1.4 engine in the Nissan Micra. It manages engine start-up, stable operation of the power unit and the vehicle’s response to the throttle pedal during everyday driving.
The Ecu engine controller 23710-1F720 is an electronic module that collects data from sensors and controls engine operation based on this information. Thanks to it, the Nissan Micra operates smoothly and predictably in various conditions.
Yes, the designations 237101F720 and 23710-1F720 are different ways of writing the same part number. Both refer to the same Nissan Micra Ecu engine controller.
The numbers 1F72050200 and 1F720-50200 are alternative designations identifying the same Ecu engine controller. They are used interchangeably in offers and documentation.
The Ecu engine controller 0261206502 was installed in the Nissan Micra with the 1.4 engine. Exact compatibility depends on the model year and equipment version, therefore checking the vehicle VIN number before purchase is recommended.
A damaged Ecu engine controller 23710-1F720 may cause problems with starting the vehicle, uneven engine operation, the check engine warning light to illuminate or power loss while driving.
In many cases, the Ecu engine controller 1F72050200 requires matching to the vehicle immobiliser. The shop offers two variants: the Ecu engine controller in a locked and an unlocked version. Before choosing, it is worth reviewing the variant descriptions.
If the number 0261206502 matches the original controller installed in the vehicle, installation is carried out without mechanical modifications. Choosing the correct controller version is essential.
Selecting the Ecu engine controller by the number 1F720-50200 ensures compatibility with the vehicle’s electrical system and proper, stable operation of the 1.4 engine in the Nissan Micra.
The 3T designation is an additional identification symbol, found on the Ecu engine controller label. It appears together with the numbers 0261206502 and 23710-1F720.
The locked version of the Ecu engine controller 0261206502 requires immobiliser programming, while the unlocked version is prepared for easier installation. Details of the differences are described when selecting the variant in the shop.
Yes, the 0261206502 number is the original designation of the Bosch Ecu engine controller used in the Nissan Micra 1.4, which guarantees correct and safe operation of the power unit.
Cookies and related technologies enable the website to function properly and help us tailor the offer to your needs. You can accept our use of all these files and go to the store or adjust the use of files to your preferences by selecting the "Customize consents" option.
Here you can specify your preferences regarding our use of cookies.
These files are necessary for the operation of our website, so you cannot disable them.
These files enable you to use other functions of the website (other than those necessary for its operation). Enabling them will give you access to the full functionality of the website.
These files allow us to analyze our online store, which may contribute to its better functioning and adaptation to the needs of Users.
Thanks to these files, we can conduct marketing activities.
