A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine Controller NISSAN MICRA MEC37-320 FT MEC37320
Vendors's code: MEC37320
Product code: MEC37-320
Barcode:
Code 39:
ISBN:
325,20 zł
Price
325,20 zł
Regular price:
325,20 zł
0%
400,00 zł
Price
400,00 zł
Regular price:
400,00 zł
0%
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller NISSAN MICRA MEC37-320 FT MEC37320
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control computer Ecu engine controller Nissan Micra MEC37-320 MEC37320
Ecu engine controller MEC37-320, also known as MEC37320, is a matched part for Nissan Micra that supports even and stable engine operation in everyday use.
What is the Ecu engine controller MEC37-320 FT used for in the Nissan Micra?
The Ecu engine controller MEC37-320 FT is responsible for the correct operation of the engine in the Nissan Micra. It controls basic processes, such as engine start-up, stable operation and the vehicle’s response to the throttle during everyday driving.
What role does the Ecu engine controller MEC37320 play?
The Ecu engine controller MEC37320 is an electronic module that collects data from sensors and manages engine operation based on this information. Thanks to it, the Nissan Micra runs smoothly and without issues on a daily basis.
Do MEC37-320 FT and MEC37320 refer to the same Ecu engine controller?
Yes, the designations MEC37-320 FT and MEC37320 refer to the same Ecu engine controller used in the Nissan Micra. The difference only results from the way the part number is written.
In which versions of the Nissan Micra is the Ecu engine controller MEC37-320 used?
The Ecu engine controller MEC37-320 was installed in selected versions of the Nissan Micra. Exact compatibility depends on the model year and engine version, therefore checking compatibility by the VIN number before purchase is recommended.
What symptoms can a faulty Ecu engine controller MEC37320 cause?
A damaged Ecu engine controller MEC37320 may cause problems with starting the vehicle, uneven engine operation, the check engine warning light to illuminate or power loss while driving.
Does the Ecu engine controller MEC37-320 FT require programming?
In many cases, the Ecu engine controller MEC37-320 FT requires matching to the vehicle immobiliser. The shop offers two variants: the Ecu engine controller in a locked and an unlocked version. Before choosing, it is worth reviewing the variant descriptions.
Does the Ecu engine controller MEC37320 fit without modifications?
If the number MEC37320 matches the original controller installed in the vehicle, installation is carried out without mechanical modifications. Choosing the correct controller variant is essential.
Why is it worth selecting the Ecu engine controller by the number MEC37-320 FT?
Selecting the Ecu engine controller by the number MEC37-320 FT ensures compatibility with the vehicle’s electrical system and proper, stable operation of the engine in the Nissan Micra.
What is the difference between a locked and unlocked Ecu engine controller MEC37320?
The locked version of the Ecu engine controller MEC37320 requires immobiliser programming, while the unlocked version is prepared for easier installation. Detailed information is available in the variant description in the shop.
Is MEC37-320 FT an original Nissan Ecu engine controller?
Yes, the MEC37-320 FT number is the original designation of the Ecu engine controller used in the Nissan Micra, which guarantees correct and safe operation of the power unit.
