The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine Controller RENAULT CLIO 1.2 Magneti Marelli IAW5NR2C5 8200181482 16481134 8200285314 16698014
Vendors's code:
Product code: 255B-9055E
Barcode:
Code 39:
ISBN:
€142.28
Price
€142.28
€175.00
Price
€175.00
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller RENAULT CLIO 1.2 Magneti Marelli IAW5NR2C5 8200181482 16481134 8200285314 16698014
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control unit Ecu engine controller IAW5NR2C5 8200181482 8200285314 Renault Clio 1.2
Ecu engine controller IAW5NR2C5 by Magneti Marelli, also appearing under the numbers 8200181482, 16481134, 8200285314 and 16698014, is a matched part for Renault Clio 1.2, ensuring calm and even engine operation on a daily basis, available in a locked or unlocked version – before purchase, it is worth checking the description of the variants.
What is the Ecu engine controller IAW5NR2C5 in Renault Clio 1.2?
The Ecu engine controller IAW5NR2C5 is a component, that is responsible for the correct operation of the 1.2 engine in Renault Clio. It controls engine operation during start-up and everyday driving, ensuring smooth and stable vehicle performance.
What role does the Ecu engine controller 8200181482 play?
The Ecu engine controller 8200181482 manages the operation of the power unit based on information from the vehicle. Thanks to it, the engine responds correctly to the accelerator and runs evenly in various driving conditions.
Do the numbers IAW5NR2C5, 16481134 and 8200285314 refer to the same controller?
Yes, the designations IAW5NR2C5, 16481134 and 8200285314 refer to the same Ecu engine controller. Different numbers result from Magneti Marelli manufacturer markings and the Renault brand, but the application remains identical.
Which Renault Clio versions does the Ecu engine controller 16698014 fit?
The Ecu engine controller 16698014 is used in selected Renault Clio versions with the 1.2 engine. If this number is found on your controller, it means correct matching to a specific vehicle.
Is the Ecu engine controller IAW5NR2C5 available in different variants?
Yes, the Ecu engine controller IAW5NR2C5 is available in two variants: locked and unlocked. Before choosing the appropriate version, it is worth reading the variant descriptions, to match the controller to your vehicle.
When is it worth replacing the Ecu engine controller 8200181482?
Replacement of the Ecu engine controller 8200181482 may be necessary, when problems with starting the car occur, uneven engine operation or incorrect electronics behavior. A functional controller restores everyday driving comfort.
Why is the Ecu engine controller number 8200285314 so important?
The number 8200285314 allows precise matching of the Ecu engine controller to the appropriate Renault Clio 1.2 version. Part number compatibility is the key to proper operation and trouble-free installation.
