A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Skoda Octavia Bosch ME7.5 06A906032SG 0261208532
Vendors's code: 0261208532
Product code: 0261208532
Barcode:
Code 39:
ISBN:
€284.55
Price
€284.55
€350.00
Price
€350.00
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine Control Unit Skoda Octavia Bosch ME7.5 06A906032SG 0261208532
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
How can you check whether the 06A906032SG ECU will fit your 2006 Octavia?
Compare the VW/Skoda number on your unit's label – it must be 06A906032SG, with Bosch number 0 261 208 532. The model year and model alone are not enough, as many ECU versions were used in the Octavia.
Engine Control Unit Skoda Octavia Bosch ME7.5 06A906032SG 0261208532
The Bosch ME7.5 is an ECU from the Motronic family, designed for petrol engines. This unit comes from a 2006 Skoda Octavia and has part number 06A906032SG. Bosch number 0261208532 begins with 0 261, which also indicates a petrol engine ECU. The unit controls injection, ignition and the throttle body. It is used, fully working and in good condition.
How to identify this ECU
- 06A906032SG – VW/Skoda part number
- 0261208532 – Bosch number; shown on the label as 0 261 208 532
- ME7.5 – Bosch Motronic ECU family
We do not state the engine size, as it cannot be determined from the data for this unit – the number decides compatibility. Pay attention to the letters "SG": they denote the software or hardware version, so a unit with a different suffix is not automatically a replacement.
Symptoms that warrant checking the unit
- the engine will not start, although the fuel pump and coils are working,
- a throttle body fault or limp mode that keeps returning despite sensors being replaced,
- no connection with the unit during diagnostics,
- the engine suddenly cutting out while driving.
Before replacing the ECU, measure the supply voltages and check the wiring to the throttle body.
Locked and unlocked variant
The locked ECU has the immobiliser and data of the Octavia it came from stored in it. It is usually bought by garages that will unlock, program and adapt the unit to the customer's car themselves.
If you prefer a ready-made solution, choose the unlocked version – we prepare it before dispatch, most often within 1–2 working days. The method (PIN / CAR PASS, Virgin, IMMO OFF, auto-programming or clone) depends on the part number, software and immobiliser, and not every one is available. Ask us before you buy, or read: engine control unit variants.
Questions and answers
| What engine size is this ECU for? |
|---|
| We do not state it – match the unit by the number 06A906032SG on your ECU's label. |
| What does ME7.5 mean? |
| It is a family of Bosch Motronic ECUs for petrol engines. |
| What condition is the 06A906032SG ECU in? |
| Used, fully working, in good condition. You will find the warranty period in the product specifications table. |
| How long does it take to prepare the unlocked version? |
| Usually 1–2 working days before dispatch. |
Send us the numbers from your ECU at contact@auto24parts.com – we will confirm compatibility.
