A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen, Audi Bosch 05E907309C 0261S21180
Vendors's code: 0261S21180
Product code: 0261S21180
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
How can you check whether the 05E907309C ECU fits your Volkswagen or Audi?
Compare VW number 05E907309C and Bosch number 0 261 S21 180 with the label on your ECU. This is a used unit in working order for Volkswagen and Audi petrol vehicles, offered in the locked version only.
Engine Control Unit Volkswagen, Audi Bosch 05E907309C 0261S21180
The Volkswagen Group assigned the number 05E907309C to this Bosch engine control unit, while the manufacturer itself designates it 0261S21180. The 0 261 prefix indicates a petrol engine ECU. The data lists Volkswagen and Audi without a specific model, so the fit depends solely on the numbers matching the unit in your vehicle. As this unit is supplied in the locked version only, buying it makes sense mainly if you have a workshop that will program the ECU after fitting. It is also a good idea to keep the old unit until the work is finished.
Numbers on the label
- 05E907309C – Volkswagen / Audi part number
- 0261S21180 – Bosch number, shown on the label as 0 261 S21 180
The final letter C identifies the version – an ECU with the same base number but a different letter may have different software. Compare the full number.
Fault symptoms
- the engine won't start despite a working fuel supply,
- engine warning light and limp mode,
- no communication with the ECU during diagnostics,
- rough running not explained by the sensors or coils.
Before ordering the unit, check the fuses, earths and ECU connector. Only once the power supply and wiring loom are in order is replacing the ECU justified.
Locked version only
We sell this ECU in the locked version only. Its memory holds the data and immobiliser of the previous vehicle, so it is intended for workshops that will program and match it to the vehicle themselves. We do not offer a version prepared before dispatch for this unit.
If you'd like to understand the differences between ECU options, see the page ECU preparation options.
Questions and answers
| Can I order this ECU unlocked? |
|---|
| No, we offer this unit in the locked version only. |
| Will it start the vehicle straight after fitting? |
| No. It needs to be programmed and matched to the immobiliser by a workshop. |
| Which model does 05E907309C fit? |
| The data does not specify a model – check the number on your ECU. |
| What condition is the ECU in? |
| It is a used part, in working order and in good condition. You will find the warranty period in the product features table. |
Send any questions about this unit to contact@auto24parts.com.