A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen, Audi 1.9 TDI Bosch EDC16U31 038906016AK 0281014255
Vendors's code: 0281014255
Product code: 0281014255
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Where can I find number 038906016AK on the 1.9 TDI ECU?
VW number 038906016AK and Bosch number 0 281 014 255 are printed on the label on the casing. This used, working EDC16U31 ECU comes from a 2008 vehicle with the 1.9 TDI engine (Volkswagen, Audi).
Engine Control Unit Volkswagen, Audi 1.9 TDI Bosch EDC16U31 038906016AK 0281014255
Taken from a 2008 vehicle, this Bosch EDC16U31 ECU managed a 1.9 TDI engine. In our records it is assigned to Volkswagen and Audi vehicles – choose the model by number. The VW part number is 038906016AK and the Bosch number is 0281014255. The module manages injection and the running of the diesel engine. Condition: used, working, good.
Markings of this module
- 038906016AK – VW part number
- 0281014255 – Bosch number, as printed on the label 0 281 014 255
- EDC16U31 – Bosch Electronic Diesel Control ECU family
The AK suffix distinguishes this module from other 038906016 ECUs – it denotes the software and hardware version. Even the next letter along can mean different software.
Symptoms of a faulty ECU
- the 1.9 TDI engine will not start, even though the starter motor and fuel supply are fine,
- the ECU cannot be read during diagnostics,
- limp mode with reduced power,
- module damage after water ingress.
Before ordering a module, check the fuses, earths and the ECU connector. Only when the wiring is sound and the engine still does not respond is the ECU itself the most likely cause.
EDC16U31 options
You can choose a locked or unlocked ECU. The locked version keeps the data and immobiliser of the donor vehicle and is intended for workshops that will carry out the unlocking, programming and matching themselves. The unlocked version is prepared before dispatch – this usually takes 1–2 working days.
The available methods (PIN / CAR PASS, Virgin, IMMO OFF, auto programming, cloning) depend on the number, software and immobiliser. Please ask before buying and see the description of the ECU preparation options.
Questions and answers
| Will 038906016AK replace 038906016AL? |
|---|
| Do not assume so – they are different versions. Compare the full number with the label. |
| Which vehicle does the ECU fit? |
| Volkswagen and Audi vehicles with the 1.9 TDI engine and an identical ECU number. |
| What condition is the module in? |
| It is a used part, in working order and in good condition. You will find the warranty period in the product features table. |
Any questions? Email contact@auto24parts.com.