A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller VOLKSWAGEN SEAT 0281017093 03L906018HL EDC17C46
Vendors's code: 03L906018HL
Product code: 0281017093
Barcode:
Code 39:
ISBN:
1 463,41 zł
Price
1 463,41 zł
1 800,00 zł
Price
1 800,00 zł
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller VOLKSWAGEN SEAT 0281017093 03L906018HL EDC17C46
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU Engine controller VOLKSWAGEN SEAT 0281017093 03L906018HL
Tested engine control unit for Volkswagen and Seat with numbers 0281017093 and 03L906018HL, with warranty and fast shipping.
ECU Engine controller VOLKSWAGEN SEAT 0281017093 03L906018HL EDC17C46
Which Volkswagen and Seat models use the 0281017093 engine controller?
The EDC17C46 engine controller with part number 0281017093 was used in a wide range of VAG group models with 2.0 TDI CR engines. The 03L906018HL module can be found in cars like the Volkswagen Golf, Passat, Tiguan, and Seat Leon or Alhambra, ensuring precise management of the Common Rail system.
What is the function of the Bosch EDC17C46 module 03L906018HL?
The 03L906018HL ECU manages fuel injection, turbocharger pressure, and DPF regeneration. The 0281017093 module analyzes signals from numerous sensors to provide the 2.0 TDI engine with optimal performance while meeting emission standards.
Symptoms of a faulty 03L906018HL controller in a 2.0 TDI engine?
A damaged 0281017093 engine computer may result in starting issues, limp mode, or CAN bus communication errors. Every EDC17C46 controller we offer is electronically verified before being shipped to the customer.
Why is part number 03L906018HL essential for ECU selection?
Correct selection by the number 03L906018HL ensures that the controller's software matches your Volkswagen or Seat hardware configuration. Using the 0281017093 module ensures full compatibility with the factory immobilizer and safety systems.
Does the 0281017093 engine controller require programming?
Yes, the ECU Engine controller VOLKSWAGEN SEAT 0281017093 03L906018HL EDC17C46 requires professional programming to the vehicle's security system. Using a proven module with identical numbers simplifies the adaptation process.
