A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen, Seat Bosch EDC17C46 03L906018HL 0281017093
Vendors's code: 0281017093
Product code: 0281017093
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Where can I find number 03L906018HL on the ECU casing?
Number 03L906018HL is printed on the ECU sticker next to Bosch number 0281017093 (0 281 017 093) and the EDC17C46 designation. We sell this used, working module for Volkswagen and Seat diesels locked or unlocked.
Engine Control Unit Volkswagen, Seat Bosch EDC17C46 03L906018HL 0281017093
The Bosch EDC17C46 is an ECU from the EDC family, i.e. Electronic Diesel Control. Unit 03L906018HL comes from a Volkswagen or Seat with a diesel engine and is responsible for, among other things, the fuel quantity, injection pressure and turbo boost. On the sticker you will find the full set of numbers needed for comparison.
Numbers on the label
- 03L906018HL – VW part number
- 0281017093 – Bosch number, shown on the label as 0 281 017 093
- EDC17C46 – Bosch ECU family
03L906018 ECUs come in many versions marked by letters at the end. HL is a specific software and hardware version – compare it carefully with the number in your vehicle.
What to look out for before replacing it
- the engine will not start and the tester cannot connect to the ECU,
- limp mode and loss of power with no damage to the engine ancillaries,
- internal module faults stored in the memory,
- failure after water entering the ECU compartment or a voltage spike.
First rule out problems with the power supply, fuses and wiring loom.
Choose your ECU version
We send ECU 03L906018HL locked – with the data and immobiliser of the previous vehicle, for a workshop that will unlock, program and match it itself – or unlocked, prepared in-house, usually within 1–2 working days.
Which method (PIN / CAR PASS, Virgin, IMMO OFF, auto programming, cloning) will be possible depends on the number, software and immobiliser in the vehicle. Please ask before buying, and see the details on the ECU preparation options page.
Questions and answers
| Will a module with a suffix other than HL work in the same way? |
|---|
| Not necessarily – a different letter means a different version. Look for number 03L906018HL. |
| Does the ECU need coding after fitting? |
| For the locked version, yes. For the unlocked version, we agree the scope of work before purchase. |
| What condition is the ECU in? |
| Used, in working order and in good condition. You will find the warranty period in the product features table. |
Email contact@auto24parts.com with the numbers from your ECU – we will check which options are available.